![background image](http://html.mh-extra.com/html/smc-networks/jxcl1-series/jxcl1-series_operation-manual_1299622081.webp)
- 80 -
No.JXC
※
-OMV0005-A
4
IO-Link
master
detects a
problem
(COM LED is
ON)
Communi
cation failure
between
IO-Link
master and
the master of
the IO-Link.
Make sure that the IO-Link
master and the master of the
IO-Link are established.
Verify that power is supplied to the
master of the IO-Link master.
Check if there are broken cables or
loose connectors of the cable between
the IO-Link master and the master of
the IO-Link master.
When there are broken cables, replace
the cable and connect the cables
correctly.
IO-Link
matching
failure
When the matching level of
connection port for the JXCL1
controller is "TYPE_COMP (type
is compatible)", confirm that the
JXC controller and device ID
registered to the master are
matched.
Connect a JXCL1 controller for which
the device ID matches with the device
ID registered to the master.
→
10.2.2 ISDU Parameter (P.
When the matching level of
connection port for the JXCL1
controller is "IDENTICAL
(complete match)", confirm that
the JXC controller and serial No.
registered to the master are
matched.
Connect a JXCL1 controller for which
the device ID matches with the serial
No. registered to the master.
→
10.2.2 ISDU Parameter (P.
IO-Link
communi
cation mode
is not
transferred to
"Operate
mode."
Check the contents of the
"device access lock" for the
JXCL1 controller and the setting
of "data storage back up level
”
for the port connected to the
IO-Link master.
Unlock the data storage function using
the JXCL1 controller "device access
lock" setting.
Or, disable the data storage back up level
for the port connected to the JXCL1
controller of the IO-Link master.
→
10.2.2(1-2)Device Access Locks(P.
5
Communication
fault
(JXC
-
W2A-C)
The USB
driver is not
installed
Check that the USB driver for the
conversion unit is installed.
Please install the USB driver of the
communication unit.
The USB driver's installation starts when
the communication unit is connected with
PC. Details of the installation procedure
are shown in "Installation procedure of
the JXC-W2 setting software".
Incorrect
COM port
setting
Please confirm if the correct
COM port is set to the ACT
Controller.
The COM port allocated to the controller
is different for different PC’s. Check and
confirm the COM port number with the
controller connected to the PC.
The COM port number can be checked
using the Device Manager of the PC.
For details of the COM port checking
and setting methods refer to the
"JXC-W2 Controller Configuration
Software Installation Manual".
Connection
failure
Please confirm the connection
status.
Please confirm motor controller (JXC) =
communications cable = communication
unit = USB cable = PC is connected. For
example, communication cannot be
established if the connector has been
damaged.
Please confirm the power supply of
motor controller (JXC) has been turned
ON. Communication cannot be
established if the power supply is OFF.
If equipment other than the motor
controller (JXC) (PLC and measurement
equipment) is connected with PC,
remove these before checking. (There is
a possibility that the communication with
other equipment interferes in PC.)
Actuator
operates
abnormally
Misuse of
Data storage
Check the model number of the
controller to replace is the same
as the controller to be replaced.
Check the parameter for the
connected actuator was written
to the JXC controller with
JXC-BCW, if the controller is
replaced with JXCL1
-BC.
Replace with the JXC controller which is
the same model number of the controller
to be replaced. If the controller is
replaced with JXCL1
-BC, replace the
controller after writing the parameters
for the connected actuator with
JXC-BCW.