![background image](http://html1.mh-extra.com/html/smc-networks/ex600-sdn1/ex600-sdn1_maintenance-manual_1299355002.webp)
EX600-TFL26GB
8. Wiring (continued)
Wiring connection with handheld terminal
Refer to “Handheld Terminal Operation Manual” for the connection with
the handheld terminal.
1
2
3
4
5
Note
Be sure to place a seal cap on any unused connectors. Placing the
seal cap appropriately enables the unit to achieve IP67 protection.
BUS IN
Status indication LED (see figure below) displays the power
supply status and communication status. These can be checked
according to the following:
<Display status>
Indicator
symbol
Status
Indicator
symbol
Status
OFF
Flashing Red
Red Light ON
Flashing Red and
Green alternately
Green Light ON
Flashing Green
9. Trouble Shooting
<Common for SI Units>
Indicator
Status
Power for control/input is OFF.
Unit is operating normally.
Abnormal power voltage for control/input. Check the power
supply and adjust or replace it.
Abnormal power voltage for output. Check the power
supply and adjust or replace it.
Component failure inside SI unit.
When ST(M) indicator is red, stop using the product and
contact SMC.
•Valve is in short circuit or open circuit.
•Valve ON/OFF counter has exceeded the set value.
Communication error between units, or configuration memory
error.
Check the connection between units, or the unit configuration.
Error diagnostics detected the error of a unit other than the
SI unit.
<SI Unit - DeviceNet
TM
>
Indicator
Status
Power is OFF.
Communicating normally.
Checking node address duplication.
Critical communication error.
Check the node Address or Data Rate etc.
Connection cannot be established.
Non-critical communication error.
Check the Data Rate etc.
Performing self diagnostics at start up.
Component failure inside SI unit. Stop using the product
and contact SMC.
Note
Be sure to connect a termination resistor at both ends of the
DeviceNet
TM
trunk line.
Turn-lock mechanism
of the connector
Signal name
Pin No.
Wire colour
DRAIN
1
Drain
V+
2
Red
V-
3
Black
CAN H
4
White
CAN L
5
Blue
Turn the connector clockwise. It stops when turned 1/4 turn.Turn it
further. When the connector is turned 1/2 turn from the original
position, the projected portion is set at the diagonal position to the
mark and the turn is completed. Check that the connector is
securely locked.
If the connector is turned excessively, it will become difficult to
remove.
<Mounting the marker>
Mount the marker (EX600-ZT1) into the marker groove as required.
<Connection>
10. Contact
AUSTRIA
(43) 2262 62280 NETHERLANDS
(31) 20 531 8888
BELGIUM
(32) 3 355 1464 NORWAY
(47) 67 12 90 20
CZECH REP.
(420) 541 424 611 POLAND
(48) 22 211 9600
DENMARK
(45) 7025 2900 PORTUGAL
(351) 21 471 1880
FINLAND
(358) 207 513513 SLOVAKIA
(421) 2 444 56725
FRANCE
(33) 1 6476 1000 SLOVENIA
(386) 73 885 412
GERMANY
(49) 6103 4020 SPAIN
(34) 945 184 100
GREECE
(30) 210 271 7265 SWEDEN
(46) 8 603 1200
HUNGARY
(36) 23 511 390 SWITZERLAND
(41) 52 396 3131
IRELAND
(353) 1 403 9000 UNITED KINGDOM
(44) 1908 563888
ITALY
(39) 02 92711
URL http://www.smcworld.com (Global) http://www.smceu.com (Europe)
Specifications are subject to change without prior notice from the manufacturer.
© 2009 SMC Corporation All Rights Reserved.