SMAY iSWAY-FC Operation And Maintenance Manual Download

Page: 21 / 168

Operation and Maintenance Manual (DTR) iSWAY

Set of products

Version 1.8 of 2.2021

5.2.

iSWAY-WFC

is a wall-mounted unit. One variant of mounting the device is possible by

means of a KT telescopic duct placed in the wall. On one side of the duct at the end of the
installation a CDH-K air intake is mounted, and on the other side a fan.

Fig. 5.6. iSWAY-WFC

type 1.1.

5.3.

iSWAY-RFC

The iSWAY-RFC

comes in several variants with different accessories and working

positions (horizontal and vertical). The following types can be distinguished:

•

TR1 - vertical version equipped with a duct coupling.

Air flow direction

TR1 coupling

iSWAY ventilator assembly

SCR-D damper

PDA roof base

Duct length: 1000 mm

Summary of Contents for iSWAY-FC









































































































































































Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands

SMAY iSWAY-FC, Operation And Maintenance Manual

Search results

Summary of Contents for iSWAY-FC

Reviews:

Related manuals for iSWAY-FC

Brands by name

Popular brands