manualshive.com logo in svg

Smartgen HGM 9310CAN Series, User Manual

Share
Download
Smartgen HGM 9310CAN Series User Manual Download Page 65

                     

HGM93XX MPU(CAN) SERIES GENSET CONTROLLER 

HGM93XX MPU(CAN) Series Genset Controller            Version: 1.1       2016-11-03     Page 65 of 77 

14 GSM SHORT MESSAGE ALARM AND REMOTE CONTROL   

14.1 GSM SHORT MESSAGE ALARM 

When controller detects alarm, it will send short message to phone automatically. 

NOTE

:

 

All alarms about shutdown, trip and stop and trip will be sent to the pre-set phone. 

Warnings are sent to the phone according to the pre-set. 

14.2 GSM SHORT MESSAGE REMOTE CONTROL   

Users send order message to GSM module, then controller will make actions according to 

this SMS order and pass back corresponding operations information. Controllers only sent 

the message to the pre-set phone number . Detail orders as following: 

No.    SMS Orders   

Pass back Information 

Description   

1 

SMS 
GENSET 

GENSET  ALARM 

When genset is 
shutdown alarm 

status of genset 

SYSTEM IN STOP MODE     
GENSET  AT REST 

At rest status in 
stop mode 

SYSTEM IN MANUAL 
MODE 
GENSET AT REST 

At rest status in 
manual mode 

SYSTEM IN AUTO MODE 
GENSET AT REST 

At rest status in 
auto mode 

SYSTEM IN STOP MODE     
GENSET IS RUNNING 

Running status in 
stop mode 

SYSTEM IN MANUAL 
MODE 
GENSET IS RUNNING 

Running status in 
manual mode 

SYSTEM IN AUTO MODE 
GENSET AT RUNNING 

Running status in 
auto mode 

2 

SMS 
START 

GENSET ALARM 

Generator is 
shutdown  alarm 
or trip alarm   

Start genset 

STOP MODE NOT START 

Cannot start in 
stop mode   

SMS START OK 

Start in manual   
mode   

AUTO MODE NOT START 

Cannot start in 
auto mode 

3 

SMS STOP 
MODE 

SMS STOP OK 

Set as stop mode 

Summary of Contents for HGM 9310CAN Series














































































Reviews:

No comments

Brands by name

Popular brands

Load more brands