SMART SE240 Installation And User Manual Download

Page: 84 / 100

Maintaining the SMART Hub SE240

Click

Continue Anyway

Click

Finish

The

Found New Hardware

wizard closes.

You’ve connected the SMART Hub SE240 to the computer.

NOTE:

You only need to complete the new hardware installation procedure once.

In Windows Explorer, browse to

C:\Program Files\SMART Hub SE240 Update Wizard

, and

then double-click

SMART Hub SE240 x.x.x.x-Updater.exe

, where

x.x.x.x

is the current

version of the firmware.

The

SMART Hub SE240 Update

wizard appears.

Click

Next

Press and hold down

Reset

on the SMART Hub SE240 until the indicator light turns solid

yellow.

If you haven’t done so already, connect a USB cable from the second USB B receptacle on the
SMART Hub SE240 to your computer as documented on page 77.

Click

Next

Select the

Yes

option, and then click

Next

The wizard updates the firmware.

NOTE:

This may take several minutes.

Press

Next

To update the firmware

Summary of Contents for SE240





































































































Search results

Summary of Contents for SE240

Reviews:

Related manuals for SE240

Brands by name

Popular brands

SMART SE240, Installation And User Manual

Search results

Summary of Contents for SE240

Reviews:

Related manuals for SE240

Brands by name

Popular brands