SMART SE240 Installation And User Manual Download

Page: 82 / 100

Maintaining the SMART Hub SE240

NOTE:

You need a Windows computer with Internet access that you can connect to the SMART

Hub SE240 through a USB cable. The computer must have a monitor or be a laptop so that you
can view and interact with the wizards during the update process.

In your browser, go to

www.smarttech.com/SE240firmware

Click

Download

, and then follow the on-screen instructions.

After the file finishes downloading, open it.

The

SMART Hub SE240 Update

wizard appears.

Click

Next

Select the

I accept the terms in the license agreement

option, and then click

Next

Click

Next

Click

Install

The wizard installs the SMART Hub SE240 updater in the default destination folder. This may
take several minutes.

Click

Finish

The

SMART Hub SE240 Update

wizard closes.

You’ve installed the SMART Hub SE240 updater for the latest firmware version on your computer.

To install the SMART Hub SE240 updater

Summary of Contents for SE240





































































































Search results

Summary of Contents for SE240

Reviews:

Related manuals for SE240

Brands by name

Popular brands

SMART SE240, Installation And User Manual

Search results

Summary of Contents for SE240

Reviews:

Related manuals for SE240

Brands by name

Popular brands