Setup:
To setup the Zeta 50W
TM
model, choose
which battery size to use (18500/18650). Attach
corresponding battery tube to control unit. Insert
charged battery (sold separately) into the battery
tube with the positive end first. Attach desired
atomizer to top of control unit (adjust pin using
screwdriver if necessary). Turn control unit ON.
Draw on atomizer while holding the ACTIVATE
button. Adjust voltage/wattage as desired using UP
and DOWN buttons.
Display OLED:
The OLED
screen (info screen)
displays
the battery life, volts, ohms
of the attached
atomizer
, and
the
selected watts. You can increase
or decrease the watt output
using
the
UP
/
DOWN
buttons to the right of the OLED screen in 0.1 watt
increments. Or hold for 3 seconds for
rapid
UP/
DOWN.
ZETA 50W
™
Modes
:
ON/OFF
Mode
(Locked Mode)
:
Pressing the
ACTIVATE
button 5 times in less than
0
.7 seconds
will
turn
the ZETA 50W™
OFF
(Locked)
. In
locked
mode
,
the ZETA 50W™ will not power the atomizer
,
conserv
ing
battery life
and protect
ing
from unwanted
power delivery.
I
f the
ACTIVATE
button is pressed
,
the OLED screen will display “
Locked, Click 5X
”. To
turn ON
(unlock)
, repeat 5 clicks
on ACTIVATE
button
within
0
.7 seconds.
Stealth Mode:
While in locked mode
,
p
ress the
ACTIVATE
and
DOWN
button simultaneously for 5
seconds. This will activate the stealth mode. In this
mode the OLED display is
OFF
. It will still show error
messages. To switch back to normal display mode,
hold down the
ACTIVATE
and
DOWN
button
simultaneously for 5 seconds. This setting is stored
in the
internal flash memory and remains
even
if
the
battery
is
removed.
Right/Left Hand Mode:
While in the locked mode,
h
old the
ACTIVATE
and
UP
buttons simultaneously
for 5 seconds. This will
switch
the OLED display for
a left
-
handed user. To switch back to right
-
handed
display, repeat. This setting is stored to internal
flash memory and remains
even
if
the battery
is
removed.
Note: Up/Down Buttons
change with
Right
and
Left hand mode
s
.
Power Locked Mode:
Hold
both
UP
and
DOWN
buttons for 4 seconds
, this
will place the ZETA
50W™ in Power
L
ocked
M
ode. That is, the Watts
are now locked and cannot be accidentally changed.
To exit Power Locked Mode, hold the
UP
and
DOWN
buttons for 4 seconds. This setting is stored
to internal flash memory and remains
even
if
the
battery
is
removed.
Error Messages:
The ZETA 50W™
can display
the following error messages:
CHECK ATOMIZER
:
This w
ill display if the ZETA
50W™ does not detect an atomi
zer
or the
atomizer resistance is incorrect for the power
setting. (below 0.3
Ω
and above 3.3
Ω
)
SHORTED: This w
ill display if the atomizer or
wiring
have
short circuited.
CHECK BATTERY:
This w
ill display if your battery
is
unable to output
3.1V. Please insert a charged
battery.
WEAK BATTERY
:
This w
ill display if the battery
sags excessively when being activated. This
typically means the user is not using a high
-
rate
battery (IMR), or the battery is old and degraded.
It can also mean the battery is not making a good
contact or the internal board temperature is below
14
°
F
or above
140
°
F.
TOO LOW POWER:
This w
ill display if the ZETA
50W™ puts out a minimum of 3.6V. With low
power settings (7-8 watts) and low resistance
atomizers (below 2
Ω
) the ZETA 50W™ will
sometimes be unable to provide a low enough
power output to be power regulating. If this is the
case, the
Ω
display will be flashing. The device
will still operate.
Suitable Battery:
18650/18500, 3.2 - 4.3V IMR
High Discharge, 1.5 - 7 Amp Output Current.
(batteries and chargers are sold separately)
ATTENTION
:
Although the ZETA 50W™ has reverse battery
protection, please make sure to insert the battery
correctly being Positive (+) toward the top of the
device.
Device Reset:
If the battery is not able to power
the ZETA 50W™ at the desired setting, or the
battery is excessively discharged, the ZETA
50W™ may go immediately into a low voltage
shut
-
down. If activating the ZETA 50W™ causes
the screen to blank out and then displays the
welcome screen, you should charge, replace or
upgrade your battery. This is especially common
at power settings above 50 watts combined
output.
Auto Power Down:
The ZETA 50W™ OLED
display will be at full brightness while activat
ed.
A
fter
15 seconds
if a button is not depressed
, the screen
will dim.
If a button is not depressed within 2
minutes
, the screen will fade out and the ZETA
50W™ will go into sleep mode. Pressing any button
will
wake the device from sleep mode.
Operating Discharge Temperature:
The ZETA
50W™ has an onboard temperature sens
or
. It will
shut down and display “Weak Battery” if the internal
board temperature is below 14
°
F
or above
140
°
F.
ZETA 50W
™
Kit Includes;
1 x 18500 Battery Tube (shown in picture below)
1 x 18650 Battery Tube
1 x ZETA 50W™ Control Unit
1 x Mini Screwdriver
3 x Replacement Connector Screws
1 x
Instruction
Manual
ZETA 50W
™
Specs
Minimum
Typical
Max
Output Power (W)
7W
-
50W
Output Voltage (V)
3.6V
-
8.5V
Output Current (Amps)
-
-
10A
Atomizer Ohms (
Ω
)
0.3
Ω
1.5
Ω
3.3
Ω
Input Voltage
3.2V
3.7V
4.3V
Input Current (Amps)
1.5A
6A
7A
Efficiency
-
95%
-
Power Calculation Note: Power (watts) = Volts Squared/ Resistance
Activate Button
UP
Button
D
OWN
Button
OLED Display
/ Info Screen
Bottom
(Remove to insert battery)
© 2014
Smart Smoke, Inc. All rights reserved.
The ZETA 50W™ and Smart Smoke
®
Logo are trademarks of Smart Smoke Inc.
www.smartsmoke.com
1-888-356-4654
If you are not satisfied with this product for any reason, please contact us.
