SMART Embedded Computing MVME4100 Programmer'S Reference Manual Download | Manualshive

Page: 23 / 84

background image

MVME4100 Single Board Computer Programmer’s Reference (6806800H19D)

23

Chapter 3

Register Descriptions

3.1

Overview

System resources including system control and status registers, external timers, and the
QUART are mapped into a 16 MB address range accessible from the MVME4100 local bus
via the MPC8548E LBC. The memory map is defined in the following table including the
LBC bank chip select used to decode the register.

Any address that is not listed in the table below is unused and reserved for future
use.

Table 3-1

System I/O Memory Map

Address

Definition

LBC Bank/
Chip Select

Notes

F200 0000

System Status Register

4

3

F200 0001

System Control Register

4

3

F200 0002

Status Indicator Register

4

3

F200 0003

NOR Flash Control/Status Register

4

3

F200 0004

Interrupt Register 1

4

3

F200 0005

Interrupt Register 2

4

3

F200 0006

Presence Detect Register

4

3

F200 0008

PCI Bus Status Register 1

4

3

F200 0009

PCI Bus Status Register 2

4

3

F200 000A

PCI Bus Status Register 3

4

3

F200 0010

NAND Flash Chip 1 Control Register

4

3

F200 0011

NAND Flash Chip 1 Select Register

4

3

F200 0012

Reserved

4

1

F200 0013

Reserved

4

1

F200 0014

NAND Flash Chip 1 Presence Register

4

3

F200 0015

NAND Flash Chip 1 Status Register

4

3

«
...
21
22
23
24
25
...
»

Summary of Contents for MVME4100





















































































Reviews:

No comments

Related manuals for MVME4100

Brand: Variscite Pages: 42

IAC-H671 Series

Brand: Lanner Pages: 51

Brand: IBASE Technology Pages: 81

Brand: ADLINK Technology Pages: 50

Brand: Trenton Systems Pages: 46

Brand: Infineon Pages: 176

Brand: Boser Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands