SLC DALI Controller CV 1CH 4x5A 12-36V Push
S23001
Wiring diagram
S23001
Function introduction
Important:
Read All Instructions Prior to Installation
•
DO NOT install with power applied to device.
•
DO NOT expose the device to moisture.
DC Power input
CH 1:R output
CH 2:G output
CH 3:B output
CH 4:W output
Product Data
Safety & Warnings
Manual set button
Digital display
2 groups DALI
signal input & output/
Push switch input
•
Complies to DALI standards IEC 62386-102, IEC 62386-207
•
Match all DALI system in the market
•
Manual /automatically DALI address setting
•
DALI address digital indicate
•
Push dimmer/DALI dimmer optional
•
Four channels, can set addresses from one to four.
•
To work with power repeater to expand output power unlimitedly.
•
Waterproof grade:IP20
1
2
3
4
0-6
0-9
1
2
This product can be operated under DALI Dimmer mode and Push Dimmer mode while connected with DALI
master controllers and push switches respectively.
1. Switching of Two Modes
DALI and Push DIM functions cannot be used simultaneously, which can be controlled respectively by DALI
master controllers and push switches.
Operation
2. Set DALI Address Quantity
2.1.
Press and hold down both of the two buttons until numeric digital display flashes, then
release the button.
2.2.
Click first button to select “1A”, “2A”, “3A” or “4A” which means 1 address, 2 addresses, 3
addresses or 4 addresses.
2.3.
Then press and hold down any of the 2 buttons until the numeric digital display stops
flashing to confirm the setting.
For example, when we set address to 22:
When select 1A, all four channels will be the same address 22.
When select 2A, channel 1 & 3 will be the same address 22, channel 2 & 4 will be the same
address 23.
When select 3A, channel 1, 2, 3 will be address 22, 23, 24 respectively, and channel 4 address is
also 24.
When select 4A, channel 1, 2, 3, 4 will be address 22, 23, 24, 25 respectively.
3. DALI Address Assigned by DALI Masters
DALI address can also be assigned by DALI Master controller automatically, please refer to user manuals of
compatible DALI Masters for specific operations.
Note: The digital display will show When the DALI master is assigning addresses.
4. Push Dimmer Mode
While connected with a AC push switch, the digital display will show “PD” which means Push Dimmer Mode,
operations under Push Dimmer Mode are as follows:
4.1. Click the button to switch ON/OFF
4.2. Press and hold down the button to increase or decrease light intensity to desired level and release it, then
repeat the operation to adjust light intensity to opposite direction. The dimming range is from 1% to 100%.
4.2. Memory function after power off or power failure enables the device to memorize the status before power
off while power on again.
Set DALI Address Manually Via Buttons
1.1. Press and hold down any of the two buttons until numeric digital display flashes, then release the button.
1.2. Click any of the two buttons once to select a digit, click again to change the digit until the desired DALI
address appears. Click first button to set “tens” position and second button to set “units” position. The address
can be set from 00~63.
1.3. Then press and hold down any of the 2 buttons until the numeric digital display stops flashing to confirm the
setting.
Note: DALI address can be manually assigned from 00-63-FF, by factory defaults, no DALI address is
assigned for the dimmer, and the display shows . Setting DALI address as will reset the
dimmer to factory defaults.
V+ V+
1- V-
2- V-
3- V-
4- V-
V+ V-
AC Power
50/60Hz
L
N
G
V+
V-
O
U
T
P
U
T
IN
P
U
T
12V/24V/36V/48V
CV PSU
DALI Master
If Single Color LED Strip
S23001
1
2
3
4
0-6
0-9
1
2
3
4
0-6
0-9
1
2
3
4
0-6
0-9
If Connect with RGBW LED Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
V+ V+
WW WW
CW CW
WW WW
CW CW
If Connect with Dual Color LED Strip
Input
Voltage
Remarks
Output
Current
Output
Power
Size(LxWxH)
DALI
Consumption
Dimming
Range
Ambient
Temperature
•
Radio Frequency Interference acc
ording
to EN 55015:2013
•
Immunity standard acc
ording
to EN 61547:2009
•
TÜV Rheinland marked, CE marked
Conformity & Standards
PUSH DIM
L
N
DA
DA
DA
DA
DA
DA
D
A
L
I
D
A
L
I
V+
V-
V+
V-
1
2
-3
6
V
D
C
IN
P
U
T
PUSH DIM
L
N
DA
DA
DA
DA
DA
DA
D
A
L
I
D
A
L
I
V+
V-
V+
V-
1
2
-3
6
V
D
C
IN
P
U
T
PUSH DIM
L
N
DA
DA
DA
DA
DA
DA
D
A
L
I
D
A
L
I
V+
V-
V+
V-
1
2
-3
6
V
D
C
IN
P
U
T
PUSH DIM
L
N
DA
DA
DA
DA
DA
DA
D
A
L
I
D
A
L
I
V+
V-
V+
V-
1
2
-3
6
V
D
C
IN
P
U
T
S23001
S23001
