manualshive.com logo in svg

SkyWave IDP 800 Series, Hardware Manual, Page: 43 / 102

Share
Download
SkyWave IDP 800 Series Hardware Manual Download Page 43

 

IDP 800 Terminal Series - Hardware Guide 

© SkyWave Proprietary                                                    31                                                   T209, Version 01 

Parameter 

Description 

Gasoline 
Diesel Fuel 
Fuel Additives 
Alcohol 
Anti-Freeze Water Mixture 
Degreasers 
Soap and Detergents 
Steam 
Waxes 
Kerosene 
Freon 
Spray Paint 
Paint Strippers 
Ether 
Dust Control Agents (magnesium chloride) 
Moisture Control Agents (calcium chloride) 
Ammonia 
Aluminum brightener (acid wash) 

Steam Cleaning and 
Pressure Washing 

The terminal meets all of its specifications after a steam cleaning 
and pressure wash test as detailed in SAE J1455, section 4.5.3. 

Fungus 

The terminal meets all of its specifications after a fungus test as 
detailed in SAE J1455, section 4.6.3. 

Dust and Sand 
Bombardment 

The terminal meets all of its specifications after a dust and sand 
bombardment test as detailed in SAE J1455, section 4.7.3. 
The terminal meets the acceptance conditions of IEC 60529, 
section 13.6.2 after a dust and sand bombardment test as detailed 
in IEC 60529, section 13.4. 

Drop Test 

The terminal meets all its specifications after a handling drop test 
as specified in SAE J1455, section 4.11.3.1. 

3.12  Mechanical 

All dimensions are shown in millimeters. 

Summary of Contents for IDP 800 Series







































































































Reviews:

No comments