manualshive.com logo in svg

SkyWave IDP 800 Series, Hardware Manual, Page: 12 / 102

Share
Download
SkyWave IDP 800 Series Hardware Manual Download Page 12

IDP 800 Terminal Series - Hardware Guide 

T209, Version 01                                                         xii                                              © SkyWave Proprietary 

damage. The parties agree that the foregoing represents a fair allocation of risk 
hereunder. 

Warranty 

SkyWave provides a manufacturer’s warranty to the original purchaser (Solution 
Provider) that its products and services will perform in accordance with SkyWave’s 
specifications and will be free from defects in material and workmanship for a limited 
period of time. This warranty is limited to the repair and/or replacement of any defective 
components experienced under normal specified operating use and storage conditions, at 
SkyWave’s discretion. It does not cover any damages caused or associated with the 
product’s misuse. The end-user’s only remedy or recourse is against the Solution 
Provider, and any experience with defective products should be communicated to your 
Solution Provider. Shipping of defective product, back to the Solution Provider will be in 
accordance with the Solution Provider’s instructions and should be accompanied with a 
fault report. SkyWave is not responsible for corrosion damage caused by improperly 
assembled or installed cables. 

Warranty is void if unit is opened

 

or screws are over-

torqued.

 

A fault report is required for each unit returned under warranty. Please contact 
SkyWave’s Customer Support for additional information. 

User Serviceable Parts 

The terminals contain no user serviceable parts or replaceable fuses. 

 

 

Summary of Contents for IDP 800 Series







































































































Reviews:

No comments