Smart Button
TM
CA-318/ CS-318
1. INTRODUCTION
Model CA-1/ CS-1
Smart Button
TM
Garage Door Control
Congratulations on your purchase of the Skylink
®
CA-1/ CS-1 Smart
Button
TM
Garage Door Remote Control. This is a kit with a remote
control and Smart Button
TM
. Simply replaces the traditional wall button
by the Smart Button
TM
, that’s all for the installation. In this kit, you will
find the following:
Programming
Learn remote controls
Smart Button
TM
can learn up to 16 remote controls. To learn remote
controls, follow instructions below:
1. Remove the battery cover on your Skylink
®
remote, randomly
set the DIP switches to your desired combination.
2. Re-install the battery cover to your Skylink
®
remote.
3. Press the learn button on the side of the Smart Button
TM
.
4. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
5. Within 30 seconds, press the button on the remote
control you would like to program.
6. Once the remote control is programmed, the LED
will flash slowly, in the same way as it flashes
in standby mode.
7. You may now operate the garage door opener
with this remote control.
To program your car remote to the Smart Button
TM
, please refer
to the instructions for your car remote.
3. OPERATION
Rating of the transformer:
12V DC, 100mA
Diameter of DC plug : 3.5mm
1. Open up the “Easy Clip
TM
” and place it underneath
the existing 2 wires of the wall button / wall
console.
2. Ensure a pair of the wall button ribbon wires
are placed properly inside the channels of the
“Easy Clip
TM
”.
NOTE:
Ensure the ribbon wires
are not twisted but laid
flat inside the clip.
If your wall button ribbon wires
are not the AWG#22 or #24 or
the same kind as shown
in the diagram, please refer
below (4) or visit our website
www.skylinkhome.com for
more information.
2. INSTALLATION
Easy Clip
TM
Ribbon Wires
Wall Button
Ribbon Wires
Press / lock
2. INSTALLATION (CONT)
3. Press and lock the clip by snapping it together. The included Crimper
helps you lock the “Easy Clip
TM
”. Close
the cover and press down to
lock the cover using this Crimper until you hear a “click”.
If the Smart Button
TM
’s red LED does not flash after the Smart Button
TM
as
been connected to the wall button’s wires for 2 minutes, your
garage door opener is probably too old. However, the
Smart Button
TM
will still work if you plug in an adapter
(purchased separately). Please contact Skylink
®
to
purchase the adapter.
5. If the wall button wires are hidden inside the
wall, please connect the “Easy Clip
TM
” to
the exposed wires attached to the
terminals of the garage door
opener.
4. If the “Easy Clip
TM
” cannot clip with the wires from your wall button, cut
off the “Easy Clip
TM
” then connect two wires from the Smart Button
TM
to the wall button.
a) Dismount the existing wall button from the wall.
b) Connect the 2 wires from the Smart Button
TM
to your existing wall button. Polarity does not
matter, so simply pick one wirefrom the
Smart Button
TM
and connect it to one of the screw
terminals on your wall button. Connect the 2nd
wire to the other screw terminal.
c) Mount the wall button back.
If the red LED flashes slowly, the Smart Button
TM
is in
standby mode. When a valid remote control signal is
received, it will open/close the garage door.
Press the programmed button on the remote control
or Smart Button
TM
, it will open / close the garage door.
6. Power up the garage door opener, the red LED on the Smart Button
TM
should keep flashing slowly within 2 minutes.
7. Secure the Smart Button
TM
properly with the mounting accessories.
Note: Do not cut the antenna!
Straighten up the antenna to improve
signal reception.
Note:
After installation of the “Easy Clip
TM
”, if you want to re-install the Smart
Button
TM
to another place, please open the “Easy Clip
TM
” by gently unlocking
the two buckles with a screw driver, and remove it from the wires. Do not
re-use the “Easy Clip
TM
”, refer to Step 4 to re-install it.
OPEN /
CLOSE
Button
LED
DIP
switches
Learn Button
LED
Antenna
Crimper
Double Sided Tape
100P/ 100PA
Visor clip
CA-318/ CS-318 Smart Button
TM
Unplug the power cord of your garage door opener before installation to ensure
power is not connected.
DO NOT let children use the gargae door Transmitter without adult supervisor.
Children can injure themselves or others by the garage door.
DO NOT use remote to control the door without safety beams.
WARNING
Antenna
