1. INTRODUCTION
ON/OFF Control
ON/OFF Control
MR-318
Model MR-318
Screws and Accessories
TM
Thank you for your purchase of a SkylinkHome ON/OFF Control Model
MR-318. This On/Off Control allows you to wirelessly turn on and off
TM
connected lights or appliances with the SkylinkHome transmitters.
The ON/OFF Control MR-318 can communicate with up to 8 transmitters,
so user has the option to add more transmitters to the system, such as
more remote controls, or motion sensors etc.
TM
All wireless signal communications within the SkylinkHome System are
based on rolling code technology to ensure highest security is used.
The following items are included in this package:
-
ON/OFF Control
-
Screws and Accessories
CAUTION
Installation is required and enclosed instructions must be followed
carefully to all steps and notes. If you are uncertain or uncomfortable
performing this installation, please consult a qualified electrician.
This manual should also be retained for future reference.
2. INSTALLATION
OFF
ON
Remote
Works
Remote Does
Not Work
“PROG” button
Press the
desired
button
TC-318-3
1. Turn off power to the circuit that you plan on installing the ON/OFF Control
to at the circuit breaker.
WARNING
Failure to turn off power at the circuit breaker can result in electrical
shock causing severe or fatal injury.
The ON/OFF Control is designed to operate maximum load of 600W at
120VAC.
2. Follow the diagrams below to install the ON/OFF Control with the 3
wires: Neutral, Live and Load. Use the provided screws to secure the
ON/OFF Control. The grey antenna should not be cut or connected to
anything else.
3. After all the wires are connected, ensure that all of the wire connectors
are attached securely and there should be no exposed copper wiring.
Straighten the antenna after installation.
4. Secure the MR-318 to a flat surface by 2 screws or you may place it
inside the fixture.
5. Turn the circuit breaker back on and turn on the wall switch that is
used to operate this.
6. After you hear a single beep, the ON/OFF Control is installed properly
and you can start programming transmitters to the ON/OFF Control.
Note:
Antenna (grey wire) - Do not cut it, keep it as straight as possible after
installation.
3. PROGRAMMING TRANSMITTERS
In order to operate the ON/OFF Control remotely, a transmitter must be
programmed to the ON/OFF Control. Each ON/OFF Control can be
operated by up to 8 different transmitters (or 8 different command signals).
To program a TC series transmitter into the ON/OFF Control, follow the
instructions below.
1. The ON/OFF Control should be powered off initially.
This can be done by switching off the wall switch or
circuit breaker controlling the receiver module.
2. Power on the ON/OFF Control by switching on the wall
switch or circuit breaker. You will hear a beep from the
ON/OFF Control. The beep indicates the ON/OFF
Control is now in programming mode and it will stay
in this mode for 15 seconds.
3. Press the PROG button on the back of the trans-
mitter with a sharp object. The front LED will be on.
4. Press the button on the transmitter that you
would like to program into the ON/OFF Control,
the front LED will flash.
5. Once the transmitter is programmed, the ON/OFF
Control will beep, indicating you have successfully
programmed the transmitter to the On/Off Control.
Now the programmed transmitter button is ready to
be used.
Note: To program other transmitters/sensors (besides TC transmitter),
please refer to the instructions of those transmitters/sensors and the above
instructions.
4. ON / OFF OPERATION
The MR-318 ON/OFF Control allows on / off operation, when the
programmed button is pressed, it will transmit a signal to toggle the
current status of the load. For example, if a toggle signal is received when
the light is off, that signal will turn on the light.
Note:
If the ON/OFF Control is installed
after a wall switch, you can use the
transmitter to operate the light
remotely only if the wall switch is
in the ON position. If the wall switch
is off, no power is provided to the
ON/OFF Control and therefore, you
cannot operate the light remotely.
In case the transmitter is not on hand,
you can still operate the lighting
fixture with the wall switch.
This receiver offers two optional states after powered on, choose the one
which fits your requirement.
1. Power On - Light On:
1) You may use the wall switch to control the light as usual.
2) After a power outage and the electricity comes back, the light will be
on if the wall switch is in On position.
If you have a deluxe remote, you can make sure that you will actually turn
on a light by pressing [ ] first, then the programmed button. Similarly,
you can make sure that you will turn off a light by pressing [ ] first, then
the programmed button.
If you have a deluxe remote and you press [ ], all those receivers to
which the remote is programmed will turn on their loads. If you press
[ ], all those receivers to which the remote is programmed will turn
off their loads.
Before Installation
Live
(Usually Black)
Load
Live
(Usually
Black)
Neutral
(Usually White)
Neutral
(Usually
White)
(White)
(Red)
(Black)
TM
After Installation
Antenna
http://waterheatertimer.org/Remote-controls-for-home.html
