SkyLink GM-318 Quick Manual Download Page 1

2. SET UP CODE CONNECTORS AND ZONE CONNECTORS

Note: If you experience interference from a nearby system, which could
accidentally trigger your system, please change the code settings on the
sensor and receiver. The code setting on the sensor and receiver should
still match after changing the code setting.

1. INTRODUCTION

Garage Door Monitor

TM

Model GM-318

4 pcs  3 x 18 screws
1 pc  2 x 5 screw

Household Alert

®

        Receiver

3V Lithium
battery

In order for the sensor to communicate with the receiver properly, the
sensor’s code must match with the receiver’s code.  Code connectors 1
to 6 can be found by opening the battery cover of the sensor and the
back cover of the receiver.  Note: Before opening the battery cover, it is
necessary to remove the transparent protective cover. Keep it for future
use. User is required to set these code connectors randomly and the
code settings on the sensor and receiver must be the same.  Each
position of the code connector can be set to “+”, “-” or “0” position.
Refer to the diagram below to set the code connectors properly. If the
connector is placed on the top and middle posts, that column is set on
“ + ”. If the connector is placed on the middle and bottom posts, that
column is set on “ - ”. If the connector is removed completely, (not placed
on any posts), it is set to “ 0 ”. (see diagram for examples of how to set a
column to the three different positions).

1. CODE CONNECTORS

Code Connectors on  Receiver

After setting up all the connectors, both units are ready to be powered up.

Plug in the adapter to the receiver, the green LED will start flashing
indicating the receiver unit is powered up but no sensor is detected.
Push the detection rod to it’s fully retracted position. Remove the battery
cover on the sensor and insert the 3V lithium battery to the sensor as
shown in the diagram.

The LED on the sensor will flash 8 times to indicate the unit is properly
powered and there is signal transmission to the receiver.  The green LED
on the receiver will stop flashing and stay on. Make sure to put the
transparent protective cover back in place after setting up.

Plug in adapter to the receiver

4. INSTALLATION

Unplug the power cord of your garage door opener
before installation to ensure power is not connected.

 

WARNING

3. POWER UP THE HOUSEHOLD ALERT

®

  RECEIVER AND

GARAGE    DOOR MONITOR

TM

 SENSOR

Garage Door
Monitor

TM

 Sensor

Code connectors on  sensor

Remove transparent
protective cover

Clip

Note: A connector
can be removed
with the clip,
as shown.

Each receiver can work with up to 4
different sensors (to represent 4
different zones on the receiver).
There are 2 connectors that deter-
mine the zone number 1, 2, 3, or 4.
These 2 connectors can be found by
opening the battery cover.  Please
follow the chart below to set the zone
number.  If the sensor is set to zone
number 1, then the receiver zone 1
signal will correspond to this sensor.

Zone
connectors

2. ZONE CONNECTORS

“+” on the table means the connec tor for
that position should be placed on the
posts.

“-” on the table means the connector for
that position should be removed.

A

B

Zone 1

+

+

Zone 2

+

-

Zone 3

-

+

Zone 4

-

-

Table 1

Insert 3V battery to the sensor

+

“+” positive
side up

If the green LED on the receiver does not stop flashing, ensure the code
setting on the sensor is identical to the receiver. Position the sensor
vertically to allow the detection rod to drop. One of the LED on the
receiver will flash and the buzzer will also beep. Please put the battery
cover and transparent protective cover back in place.

You can install the sensor onto the garage door.

Note: The receiver may not be able to receive the signal from the
sensor properly if they are too close to each other. Move the sensor
further from the receiver to test again.

Detection
rod is fully
extended

Detection
rod is fully
retracted

Step 1 – Select a spot on your garage door to mount the sensor

Before you install the sensor onto the garage door, make sure the
garage door is closed.  The sensor assembly should be mounted on one
of the vertical supports of your garage door near the bottom.

When the door is closed, the detection rod should be retracted.  When
the door is open, the detection rod will be extended.

2. SET UP CODE CONNECTORS AND ZONE CONNECTORS (CONT)

‘+’

‘-’

0

The garage door monitor

TM

 is designed to monitor the status of your

garage door and advise you if the door is open.  By placing the sensor
on the door panel, you will be alerted when the door is open.  When the
garage door is open, receiver will beep and flash.

In this package, you should find a 

 

Garage Door Monitor

TM

 Sensor,

 

a

Household Alert

®

 Receiver, an adapter, 3V lithium battery, double-sided

foam tape, mounting accessories and a clip.

Please follow the instructions below to set up your garage door monitor
properly.

Adapter

Double-sided foam tape

 Clip

Reviews: