manualshive.com logo in svg

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2, User Manual, Page: 5 / 56

Share
Download
Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 User Manual Download Page 5

4O3A Signature – Antenna Genius User Manual

 

Index

 

 

 

Page 

4

 of 

55

 

 

3. 

LEGAL 

3.1. 

Radio & Television interference 

(FCC Part 15 - §15.21 and §15.105)

 

 

 

 

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:

 

Reorient or relocate the receiving antenna.

 

Increase the separation between the equipment and receiver.

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.

 

Consult the dealer or an experienced radio/TV technician for help.

 

 

You may also find the following FCC booklet helpful: 

"How to Identify and Resolve Radio-TV 

Interference Problems"

 available from the U.S. Government Printing Office, Washington D.C. 

20402. Info also available online at FCC.gov:

 

 

https://www.fcc.gov/guides/interference-defining-source

 

 
 

Changes and Modifications not expressly approved by the manufacturer or registrant of this 
equipment can void your authority to operate this equipment under Federal Communications 
Commission’s rules. 

 

3.2. 

European Community CE conformity 

 

Sky Sat d.o.o. declares Antenna Genius

TM

 8x2 complies with the European Community EMC 

standards:

 

Summary of Contents for 4O3A Signature Antenna Genius 8x2 Plus v2

























































Reviews:

No comments