manualshive.com logo in svg

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2, User Manual, Page: 47 / 56

Share
Download
Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 User Manual Download Page 47

4O3A Signature – Antenna Genius User Manual

 

Index

 

 

 

Page 

46

 of 

55

 

 

 

The OM module is connected to AG#2. Configure OM module to use Port1A signal outputs 
+12VDC, which will be used for 8xAB switch. Open AG Configuration Settings and check “2xAG 
with OM control”. Click on Save and Reboot. 

 

 

More details about OM Module configuration in chapter 11.2.

 

 

When we want to use particular antenna on AG#2, simply choose antenna input on AG#2 
(manually, band data) and the OM module will switch the desired antenna on AG#2. Note that 
antenna switching will occur without any condition or interlock. AG#1 will lose that antenna 
momently. 

 

 

GENIUS WARNING!

 

Coordinate your activity. You can switch-off antenna from AG#1 even if 

that antenna is in use!

 

11.5. 

Stacking multiple AGs into a superswitch by AB switches 

You can now combine multiple 8x2 v2 Plus units for 16x2, 24x2, and even 32x2 switching 
capability.

 

Implemented with a 

Master 

/ 

Slave 

design. Once you configure the system you will be 

connecting to the Master unit. It will be in charge for the overall logic of the system.

 

 

In the simplest scenario configuration, we use two AG 8x2 v2 Plus units and two 4O3A AB 
Switches to create 16x2 switch. 

 

 

Summary of Contents for 4O3A Signature Antenna Genius 8x2 Plus v2

























































Reviews:

No comments