manualshive.com logo in svg

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2, User Manual, Page: 23 / 56

Share
Download
Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 User Manual Download Page 23

4O3A Signature – Antenna Genius User Manual

 

Index

 

 

 

Page 

22

 of 

55

 

 

 

For this purpose, you can use the 
4O3A Manual Antenna Controller S8:

 

 

 

9. 

ANTENNA GENIUS

tm

 APP 

The AG App is used to perform six tasks:

 

 

1.

 

Programming band-antenna assignments for automated operation: antenna selection 
driven by radio band data received directly from a FlexRadio, radio, via Genius Series 
device, or relayed through a logging software.

 

2.

 

Secondary antenna selection when there is more than one antenna available for a band. 
AG will default to last antenna selected for a particular band in automatic mode after 
which operator can manually select an alternative antenna for that band. Note that you 
will be prohibited from switching to antennas which have not been programmed for the 
band in question (unless band is set to none, rendering the antenna as band 
independent).

 

3.

 

Providing a Windows interface for manual antenna selection, an alternative to 
automated antenna selection.

 

4.

 

Allowing multiple users to use one switch.

 

5.

 

Allowing remote operation.

 

6.

 

Updating AG with the latest firmware.

 

 

EXPERT TIP!

 AG will default to last antenna selected for a particular band in automatic mode after 

which operator can manually select an alternative antenna for that band. Note that you will be 
prohibited from switching to antennas which have not been programmed for the band in question.

 

9.1. 

Initial set-up 

9.1.1. Confirm DIP switches are configured as intended

 

 

First, make sure you’ve set the DIP switches to suit your installation (see Section 8.6 above) and 
you have connected DC power and the appropriate Port A and Port B control connections (LAN, 

Summary of Contents for 4O3A Signature Antenna Genius 8x2 Plus v2

























































Reviews:

No comments