manualshive.com logo in svg

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2, User Manual, Page: 19 / 56

Share
Download
Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 User Manual Download Page 19

4O3A Signature – Antenna Genius User Manual

 

Index

 

 

 

Page 

18

 of 

55

 

 

 

 

Click on a radio from the list and use the 

arrow buttons

 to assign the radio to Slice A and Slice B. 

 

 

Set 

Antenna: 

option to assign the desired Flex antenna port to Port A and Port B, respectively. 

 

 

Click 

Save & Reboot

.

 

8.9. 

4O3A Genius Series Devices Control 

In this mode AG gets band data from various Genius Series device (GSD), using the TCP/IP 
network. 

 

4O3A designs and manufactures high-quality accessories and TCP/IP controlled devices for your 
shack.  Genius Series devices capable of forwarding Band Data can be used as a band data 
source for Antenna Genius.

 

Switch on DIP 1 and DIP 2 to set PORT A to GSD control:

 

 

DIP 1

 

DIP 2

 

CONTROL MODE

 

ON

 

ON

 

GSD control

 

 

Switch on DIP 3 and DIP 4 to set PORT B to GSD control:

 

 

DIP 3

 

DIP 4

 

CONTROL MODE

 

ON

 

ON

 

GSD control

 

 

You can now connect to the FlexRadio using the app. Click the configuration icon (gear icon) on 
the top and select Configure Device:

 

 

Summary of Contents for 4O3A Signature Antenna Genius 8x2 Plus v2

























































Reviews:

No comments