manualshive.com logo in svg

Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2, User Manual, Page: 18 / 56

Share
Download
Sky Sat 4O3A Signature Antenna Genius 8x2 Plus v2 User Manual Download Page 18

4O3A Signature – Antenna Genius User Manual

 

Index

 

 

 

Page 

17

 of 

55

 

 

5.

 

remove the DC power from AG

 

6.

 

turn DC power back on

 

 

 DIPs 7 and/or 8 ON have no effect on the device in normal working mode without cycling DC 
power.  After a successful configuration reset, make sure to set DIP 7 and/or 8 to OFF, otherwise 
you will reset your configuration on every power up.

 

8.8. 

LAN Control Mode 

LAN Control Mode is used if you want to obtain band data from a FlexRadio. In this mode AG 
gets band data from a FlexRadio using the TCP/IP network.

 

 

Set DIP 1 and DIP 2 to OFF to set PORT A to LAN control:

 

 

DIP 1

 

DIP 2

 

CONTROL MODE

 

OFF

 

OFF

 

LAN control: FlexRadio 

 

 

Switch DIP 3 and DIP 4 to FF to set PORT B to LAN control:

 

 

DIP 3

 

DIP 4

 

CONTROL MODE

 

OFF

 

OFF

 

LAN control: FlexRadio 

 

 

You can now connect your FlexRadio using the app. Click the configuration icon (gear icon) on 
top and choose Configure Radio(s):

 

 

 

 

Your FlexRadio will be discovered automatically and listed on the right:

 

 

Summary of Contents for 4O3A Signature Antenna Genius 8x2 Plus v2

























































Reviews:

No comments