manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

Share
Download
Skoda Rapid NH 2014 Workshop Manual Download Page 99

1.3

Door adjustment

Note

♦

The vehicle must be standing on its wheels in order to adjust

the rear door.

♦

The rear door is correctly adjusted if in the closed state it has

an overall even gap size, is not positioned too far inwards or

outwards and the contours are aligned.

♦

Observe the gap sizes of the front door ⇒ Body Repairs; Rep.

gr.  00 ; technical data; body gaps; front body .

♦

After carrying out adjustment work, perform corrosion protec‐

tion measures at the screws and hinges.

Setting the gap sizes
In order to correctly set the gap sizes, the screws

-2, 5, 7, and 8- must be slackened at the A pillar.
– The bottom B pillar trim panel must be removed for the screw

-5-

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

1. Rear door    

91

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands