manualshive.com logo in svg

Skoda Rapid NH 2014, Workshop Manual

Share
Download
Skoda Rapid NH 2014 Workshop Manual Download Page 218

3

Recessed handles

3.1

Removing and installing the recessed

handles of the roof

Removing
– Fold down the recessed handle - 1 - and swivel out the cap

- 2 -.

– Unlock the clips - 3 - using e.g. the release tool -T10517- or -

T10518- or -T10518A- and detach the recessed handle by

pulling from the supports.- Arrows- .

Installing
– Press recessed handle - 1 - with the supports into the bores

in the bracket for the recessed handle.

– Press in the spreader clips - 3 - until they click audibly into

place.

– Press in the cover caps - 2 -.

Rapid NH 2014 ➤ , Rapid Spaceback 2014 ➤

Body Work - Edition 10.2018

210

     Rep. gr.68 - Interior equipment

Summary of Contents for Rapid NH 2014
































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands