Skoda Fabia II 2007 Workshop Manual Download

Page: 36 / 165

The clutch pedal switch is installed from the front wall.
– Insert the clutch pedal switch into the support of the bracket

and turn it 45° in -direction of arrow-.

– Insert connector for the clutch pedal switch .
– Install the footwell vent ⇒ Heating and Air Conditioning; Rep.

gr. 80 .

1.7.2

Removing and installing crash strut

The crash strut for the clutch pedal, which is installed on the

steering column, is offered in two versions.
Version with two fixing screws
Removing
– Remove the storage area on the driver's side ⇒ Body Work;

Rep. gr. 70 .

– Release screws -arrows-.
Install
Installation is carried out in the reverse order.

Fabia II 2007 ➤ , Fabia II 2009 ➤ , Fabia II 2011 ➤ , Rapid 2011 ➤ , R ...

Gearbox 02T - Edition 05.2014

Summary of Contents for Fabia II 2007






































































































































































Search results

Summary of Contents for Fabia II 2007

Reviews:

Related manuals for Fabia II 2007

Brands by name

Popular brands

Skoda Fabia II 2007, Workshop Manual

Search results

Summary of Contents for Fabia II 2007

Reviews:

Related manuals for Fabia II 2007

Brands by name

Popular brands