Ski-Doo REV-XR 2009 Page 96 Operator'S Manual Download

Page: 96 / 151

MAINTENANCE PROCEDURES

mmo2008-003-043

INSERT TOOL

5. Loosen lock nut by turning the tool

counterclockwise (± 4 turns).

mmo2008-003-044_a

TURN TOOL COUNTERCLOCKWISE

6. Completely open the driven pulley

by using the suspension adjust-
ment tool. Insert the tool pins in
the ring holes and turn clockwise.

mmo2008-003-042

SUSPENSION ADJUSTMENT TOOL

mmr2008-042-001_a

1. Suspension adjustment tool
2. Adjustment ring

7. Remove the drive belt by slipping it

over the top of the driven pulley.

mmr2008-042-002

Install and adjust drive belt, refer to

DRIVE BELT INSTALLATION AND
ADJUSTMENT

Drive Belt Installation and
Adjustment

NOTE:

The drive belt adjustment must

be checked by an authorized SKI-DOO
dealer each time a drive belt is installed
and should be rechecked after 50 km
(30 miles).

The maximum drive belt life span is ob-
tained when the arrow on the drive belt
is directed toward the front of the vehi-
cle. This will ensure that correct direc-
tion of rotation is respected.

______________

Summary of Contents for REV-XR 2009
























































































































































Search results

Summary of Contents for REV-XR 2009

Reviews:

Related manuals for REV-XR 2009

Brands by name

Popular brands

Ski-Doo REV-XR 2009, Operator'S Manual

Search results

Summary of Contents for REV-XR 2009

Reviews:

Related manuals for REV-XR 2009

Brands by name

Popular brands