background image

Form 37711 Rev 1809

Page 1 of 14

www.skcinc.com

Back view

Belt clip

Charging jack

Low flow regulator

(beneath cap screw) 

allows 

pump to be switched from

high to low flow.

Durable RFI-shielded case

provides protection from 

radio frequency interference

between 27 and 1000 MHz.

Rechargeable battery

Built-in particulate trap

in see-through housing

protects pump.

Built-in rotameter

provides a visible check of 

relative flow rate during 

sampling from 0.5 to 5 L/min.

Accessory mounting screws

allow sampling accessories 

such as impinger holders to be 

secured to pump.

Recessed flow adjustment screw

adjusts flow rate between

1000 and 5000 ml/min.

Tamper-resistant cover

prevents changes to 

settings.

On/Off switch

Air discharge port

(beneath cap screw)

Inlet

44XR Universal Sample Pump

Cat. No. 224-44XR

Operating Instructions

863 Valley View Road, Eighty Four, PA 15330  USA • Tel: 724-941-9701 • www.skcinc.com

Figure 1.

 Front and back views of 44XR Universal Sample Pump

Introduction

Description

The 44XR Universal Sample Pump 

(Figure 1)

 is a constant flow (from 5 to 5000 ml/min) air sampler suitable for a broad range of 

applications. It is ideal for industrial hygiene studies as well as environmental testing.

Checking Pump/Kit Contents

Use the table below to verify that you received all items associated with the Cat. No. ordered. If you are missing items, contact SKC 
at 800-752-8472 (U.S. only) or 724-941-9701.

If You Ordered Cat. No.

Your Package Should Contain

224-44XR

Universal 44XR Sample Pump with NiMH battery pack and screwdriver set

224-44XRKD

Single Universal 44XR Pump Kit with pump, NiMH battery, screwdriver set, 100-240 V single charger, filter cassette 
holder, adjustable tube holder with Type A protective tube cover, exhaust port fitting, and nylon carry case

224-44XRKDH

Single Universal 44XR Pump Kit with pump, NiMH battery, screwdriver set, 100-240 V single charger, filter cassette 
holder, adjustable tube holder with Type A protective tube cover, exhaust port fitting, and Pelican carry case

Required Equipment/Media

 

1/4-inch ID (3/8-inch OD) Tygon

®

 tubing

 

PowerFlex

®

 Charger

 

Low flow accessories

 if sampling at 5 to 500 ml/min. 

See Accessories.

Inlet filter 

housing

Summary of Contents for 224-44XR















Reviews: