ENVIRONMENTAL CONDITIONS
Ambient/storage temperature
Relative humidity
Pollution degree
Overvoltage category
Altitude
Protection
OUTPUT
INPUT
GENERAL
ERPA1-240-F
40
180 - 280
150
400
1,6
5
880
50 - 60
>
0,75
160
0/4-20mA, 0/1-5V DC, 0/2-10V DC or 1k
Ω
~ 10kΩ potentiometer. (Device may be damaged at 12V DC and above voltages).
≥
0,2mA (for mA input),
≥
0,08V (for V input).
≤
0,18mA (for mA input),
≤
0,075V (for V input).
15ms.
≤
100
Ω
(for mA input),
≥
10k
Ω
(for V input).
Protection feature for reverse connection is available.
ERPA1-xxx-F-xx
90-250V AC, 50/60Hz.
W46 x H110 x D117mm (for ERPA1-x40-F and ERPA1-550-F) , W79 x H120 x D132mm (for ERPA1-570-F).
Approx. 450g (for ERPA1-x40-F and ERPA1-550-F) , Approx. 550g (for ERPA1-570-F) (boxed).
2500 Vrms between I/O terminals for 1 min.
For power line 16mm² cable (with 25mm² cable terminal) cable, for signal line can be connected 4mm² cable.
Max. 1,2Nm.
EN 60947-4-3
Rail mountable (EN60715,TH35 or G-32).
Self extinguishing plastics (According to EN 60695-11-10 V-O).
Fan is controlled with thermostat and works at temperatures over 50°C.
ERPA1-440-F
40
180 - 480
110
290
1,8
8
610
50 - 60
>
0,75
200
ERPA1-550-F
50
180
270
10
720
300
180 - 500
1,8
50 - 60
>
0,75
3A, 250V AC, NO or NC can be selected by program.
ERPA1-570-F
70
400
600
15
4000
400
Order Code
Load Current, AC51/25ºC (Arms)
Load Voltage (Vrms)
Overload Current t=1s/25°C (Arms)
Non rep. Surge current/25°C (Arms)
On-state Voltage Drop (Vrms)
Leakage Current (mArms)
I²t for Fusing t=10ms (A²s)
Frequency (Hz)
Power Factor (Cos
Φ
)
Minimum Operating Current (mArms)
Alarm Output
Input Signal
Transmission Signal
Drop-out Signal
Turn-on Time
Dynamic Input Impedance
Protection
Order code
Power supply
Dimensions
Weight
Isolation Voltage
Connection
Terminal screw torque
Product standard
Mounting
Enclosure material
Fa n (Optional)
ORDER CODE
Thank you for choosing
ENDA
ERPA1
S
eries power regulators.
ERP A 1 - 5 50 - F - V - RS
ENDA ERPA
1
Series Power Regulators
Product Basic Code
Rail Mounted
ERP
Fan (*)
Fan F
Communication
(*)
RS485 ModBus RS
Blank (N/A)
Load Voltage
AC A
Number of Pole
Single pole
1
Load Current
40A AC 40
50A AC 50
70A AC 70
Load Voltage
180 - 280V AC 2
180 - 480V AC 4
180 - 500V AC 5
Please rea this document carefully before using this product. The guarantee will be invalidated if the device is damaged by
not
following instructions detailed in the manual. The company shall not be responsible for any damage or losses
however
caused,
which may be experienced as a result of the installation or use of this product.
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah.
Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Barbaros Cad. No:18
1/4
40 -50 -70A AC
L
oad current.
280 -480 -500V AC
L
oad voltage.
0/4-20mA, 0/1-5V DC, 0/2-10V DC or 1kΩ ~ 10kΩ
P
otentiometer input.
4 Digits LED display.
Phase angel or zero-cross controlled.
Soft Start or Kick Start feature.
Overheat alarm output.
Varistor protection for peak voltages.
Vibration coil control (Optional).
RS485 ModBus
C
ommunication feature (Optional).
CE
M
arked according to European Norms.
A
A
V
V
Optional features
must
be specified at order.
90% Relative humidity for temperatures up to 20 % °C, decreasing linearly to 50% at 40°C. (Shouldn't be condensation).
-25... +60 °C / -30... +100 °C (Shouldn't be icing and condensation in ambient.)
2
II
Max. 1000m.
IP20 According to EN60529
Vibration
Control (*)
Vibration Control V
Blank (N/A)
KEEP AWAY device from exposed to corrosive, volatile and flammable gases or liquids and DO NOT USE the device in similar hazardous locations.
Avoid any liquid contact while the device is switched on. DO NOT clean the device with solvent (thinner, gasoline, acid etc.) and / or abrasive cleaning agents.
*
*
*
*
*
*
*
*
*
*
*
( )
*
