Sirona XIOS XG Select Operating Instructions And Installation Download Page 34

Page: 34 / 120

4 Installation

Sirona Dental Systems GmbH

Gebrauchsanweisung und Installation

64 08 137 D3610

D3610.201.02.09.02 11.2017

4.3

Check Firewall Settings

Please check the Firewall settings. Please go to the next section if there
is no active Firewall.

The steps required for different operating systems are described below
as examples. The same steps must be applied where separate Firewall
programs are in use:

In the Windows Control Panel, open the Windows Firewallpage:
"Start" > "Control Panel" > "Windows Firewall"

Is the Firewall active?
No: No additional settings are required.
Yes: Execute the following instructions.

In Windows 7, select the

"Allow a program or feature through

Windows Firewall" entry.

Summary of Contents for XIOS XG Select

























































































































Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands

Sirona XIOS XG Select, Operating Instructions And Installation

Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands