background image

  

10

Figure 5A.

6.7 

Use the small heat shield contained in
the fixing kit bag to cover the batteries.
Fold  this  element  by  hand  and  place
as show on figure 5B.

6.8   CHECK FOR GAS SOUNDNESS

Turn on the gas supply and check for gas
soundness  with  a  suitable  leak  detection
fluid (see BS 6891).

Please  check  all  joints  including  the  pilot
assembly.

6.9

FUEL BED ASSEMBLY

Please  refer  to  the  User’s  section  for
details  on  assembling  the  fuel  effect
components (Page 5, 6).

7

FUNCTIONAL CHECKS

Remove  the  pressure  test  point  sealing
screw  from  the  isolation  elbow  and  attach
a suitable pressure gauge.

Light  the  pilot  and  check  the  correct
operation  of  the  burner  at  all  the  flame
settings.  Refer  to  the  Operating
instructions on pages 4 and 5.

Check  that  the  inlet  gas  pressure  is  as
stated  on  page  8  when  the  fire  is  at  its
highest setting.

Once  the  fire  has  been  lit  for  5  minutes
turn  the  gas  OFF  at  the  isolating  elbow.
After  a  further  3  minutes  turn  the  gas
supply  ON  again,  if  the  gas  has  stopped
flowing,  the  Flame  Supervision  Device
(FSD) is operating correctly. Always check
that  the  gas  has  stopped  flowing  even  if
you hear the FSD valve close within the 3-
minute period.

Turn  OFF  the  appliance  and  the  gas
supply  and  refit  the  pressure  test  point
sealing screw.
Turn  ON  the  gas  supply  and  check  for
leaks  around  the  pressure  test  point
sealing  screw  with  a  suitable  leak
detection fluid.

8

CHECK FOR SPILLAGE

A  SPILLAGE  CHECK  MUST  BE
MADE  BEFORE  THE  INSTALLED
APPLIANCE  IS  LEFT  WITH  THE
CUSTOMER.  DO  THIS  TEST  WITH
ALL  THE  COALS  FITTED  AND  THE
FENDER  AND  ASHPAN  IN  PLACE.
CARRY  OUT  THE  TEST  AS
FOLLOWS:

8.1

Close  all  doors  and  windows  in  the  room
containing the appliance.

8.2

Light  the  appliance  and  set  to  the  HIGH
setting.

8.3

Leave  the  appliance  ON  for  5  minutes  then
light  a  smoke  match.  The  match  should  be
inserted 10mm below the top of the opening
and  be  pointed  upwards  at  45°  to  the
horizontal.

    Move  the  smoke  match  across  the  opening.

The  installation  is  satisfactory  if  all  the
smoke is drawn into the chimney.

DOWN  90.00°  R 1.00 

DOWN  90.00°  R 1.00 

DOWN  90.00°  R 1.00 

A

Figure 5B

A

RECIVER

V.11.07

Summary of Contents for Mystique ECO 4
















Reviews: