Siqura HSD62x PRH Network Cameras
Outdoor IP PTZ dome with Day/Night, WDR, Pressurized Housing
Quick Start Guide
RJ-45 connector LEDs
Green indicates a good
network connection; yellow verifies network
activity.
To mount the HSD62X with the mini wall mount
1.
Make a hole in the wall or metal access plate for the cables and secure the supplied cable gland in
the wall.
2.
Ensure that the weather resistant gasket is correctly attached to the mount.
3.
Thread the cables through the wall mount and screw it onto the wall.
4.
Attach the waterproof boot to the mini wall mount.
5.
Thread the cables through the outdoor tube adaptor and fix it to the mini wall mount with the
supplied screws and washers.
6.
Clip the safety wire to the dome camera.
7.
To keep insects out, block the cable entry hole with the supplied sponge.
8.
Connect the cables to the dome camera.
9.
Attach the dome to the outdoor tube adaptor and fasten them together with the supplied screws.
Step 1: Product Inventory
Figure 1 HD62xWDR package contents
Before proceeding, ensure that the HSD62x PRH package contains the items
listed below.
Please note that the wall mounts must be ordered separately.
HSD62x camera
(622 and 626
include outdoor
tube adaptor)
30 cm cable harness
Optical cover
Waterproof boot
Security
TORX
M3 screws
Lubricant
Quick Start
Guide
Step 2: Cabling
For operation, the HSD62x/SFP camera requires the following:
CAT-5 Ethernet cable with an RJ-45 connector
or
An SFP module as described in the XSNet™ SFP data sheet and fiber optic
cable and connectors compatible with the chosen SFP module.
A cable harness for power, analog video, and audio transmissions, equipped
with a 22-pin connector for connecting to the HSD62x (table 1).
Figure 2 Cable harness components
Figure 4 22-pin
connector pins
24 VAC
Ground (GND)
24 VAC
Step 3: 22-Pin Connector Definition
Table 1 22-pin connector assignments
Pin
Definition
Cable
Color
Rating
1
AC 24-1/DC(+)
20/18 AWG
Red
2
Alarm out NC
White
Photo Relay output 300V
3
AC 24-2/DC(-)
20/18 AWG
Black
4
Alarm out, NO
White/black
Photo Relay output 300V
5
FG
20/18 AWG
Yellow
6
Alarm out COM
24 AWG
Green/black
Photo Relay output 300V
7
Audio in
Yellow/black
8
Audio out
Orange/black
9
Audio GND
Green/black
10
Audio GND
Brown/black
11
ISOG
Blue/white
12
Alarm 1
Red/white
Input 5V 10KO pull up
Photo Relay output 300V
13
Alarm 2
Purple
14
Alarm 3
Gray
15
Alarm 4
Blue
16
Alarm 5
White/black
17
Alarm 6
Orange/black
18
Alarm 7
Purple/white
19
Alarm 8
Gray/black
20
Alarm GND
Brown/white
Input 5V 10KO pull up
21
Video GND
20 AWG
Black/gray
22
Video
Red/gray
Step 5a: Installing with a Mini Wall Mount
Installation requires the following tools:
Dome camera
Supplied waterproof boot
Mini wall mount
Screws and screw anchors
Screwdriver and drill
Figure 9 Mini wall mount
Figure 5 RJ-45
connector LEDs
24 VAC
Ground (GND)
24 VAC
Figure 3 Power input details
Step 4: Wall Mount Installation
To prepare the HSD62x for installation
1.
Remove the outdoor tube adaptor by rotating counter clockwise (figure 8a).
2.
Rotate to remove the protective cover.
3.
Make a note of the IP address on the label attached to the cylindrical heat sink.
4.
Remove the PE cloth and take off the lens cap.
5.
Generously apply the supplied lubricant to the optical cover’s waterproof boot to
ensure an IP66 quality installation (figure 8b).
6.
Loosen the screw head alignment pins on the dome cover by turning
clockwise
and line up the alignment pin and screws on the optical cover with the holes in
the dome body.
7.
Attach the optical cover to the dome body by pressing gently down on the sides
of the dome cover (figure 9c).
8.
Turn the screw head alignment pins
counter-clockwise
with a suitable screwdriver
to lock the dome into place and secure the dome with the included Phillips-head
or TORX screw.
Figure 6 Siqura WM01A
Mini Wall Bracket
Figure 7 Siqura WM03A
Gooseneck Tube
Figure 8a (left), b
(center), c (right)
Removing the outdoor
tube adaptor (left).
Lubricating the optical
cover’s waterproof boot
(center).
Attaching the optical
cover to the dome body
(right).
SFP end cap
accessory
Warning:
Fully torque down the mounting bolt that attaches the WM02 tube
adapter to the mounting bracket to prevent any movement of the camera due to
wind, vibration, etc.
Make sure the camera cannot move at all in its bracket after installation. Any
movement of the camera in its bracket can compromise positional accuracy.
© Siqura B.V. 2016
Version 1.2 (101310-1.2)
SiqHSD62xPRH QSG (MW10)
www.siqura.com
www.tkhsecurity.com
