118
419050/B
Verifying the quality of the gate valve
installation
Once the mounting flange, gate valve and transducer dock have been installed, a quality
inspection must take place. The inspection shall verify that the units has been installed
correctly, and that the hull unit can be mounted on top of the transducer dock.
Prerequisites
Neither tools nor instruments are required.
Context
The mounting flange must be mounted so that its top mating surface is in parallel with
the sea surface during normal operating conditions. The transducer dock on top of the
gate valve must remain vertical during the same conditions.
The top mating surface of the transducer dock must be protected with a wooden cover at
all times until the hull unit is installed. It is very important that this surface is clean and
undamaged, because it must be watertight after the hull unit has been installed.
Objects protruding from the hull will generate turbulence and flow noise. This will
reduce the SC90 performance. Protruding objects may be zinc anodes, transducers or
even the vessel's keel. Holes and pipe outlets are also important noise sources, as well as
rough surfaces caused by bad welding. Even traces of sealing compound, sharp edges,
bolts or empty bolt holes will create noise.
The following requirements must be met:
• All measurements are made and the results are written down.
• The top of the transducer dock is in parallel with the water line.
• The top mating surface on the transducer dock is clean without sand, dust or any
other destructive particles. Is is even and smooth without scratches, dents or other
physical damage.
• The gasket or O-ring on the top of the transducer dock is not damaged.
• The installation of the gate valve has left enough space to access end switches and (if
relevant) hydraulic connections.
• If relevant, the hydraulic system has been installed as specified in the relevant
documentation.
• The hull plating surrounding the mounting flange is even and smooth without
protruding objects that can cause noise.
• All necessary preparations have been made to design and install sufficient support
brackets.
Simrad SC90 Installation Manual
Summary of Contents for SC90
