background image

Preface

Disclaimer

As Navico is continuously improving this product, we retain the right to make changes to the
product at any time which may not be reflected in this version of the manual. Please contact
your nearest distributor if you require any further assistance.

It is the owner’s sole responsibility to install and use the equipment in a manner that will not
cause accidents, personal injury or property damage. The user of this product is solely
responsible for observing maritime safety practices.

NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL
LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE
OR THAT MAY VIOLATE THE LAW.

This manual represents the product as at the time of printing. Navico Holding AS and its
subsidiaries, branches and affiliates reserve the right to make changes to specifications
without notice.

Governing Language

This statement, any instruction manuals, user guides and other information relating to the
product (Documentation) may be translated to, or has been translated from, another
language (Translation). In the event of any conflict between any Translation of the
Documentation, the English language version of the Documentation will be the official
version of the Documentation.

Copyright

Copyright © 2016 Navico Holding AS.

Warranty

The warranty card is supplied as a separate document.

In case of any queries, refer to the brand website of your display or system: www.navico.com/
commercial.

Regulatory statements

This equipment is intended for use in international waters as well as coastal sea areas
administrated by member states pursuant to international conventions.

The R3016 12U/6X Radar system complies with:

the Navigation requirements of Marine equipment directive (MED) 96/98/EC, and the last
modification by directive 2015/559/EU, Annex A.1. item 4.36, Radar equipment for CAT 3
vessels.

The relevant Declaration of Conformity is available on the product's section on the following
website: www.navico.com/commercial.

Wheelmark

The Marine Equipment Directive 96/98/EC (MED) applies to all ships for which safety
certificates are issued by - or on behalf of - member states pursuant to international
conventions. This applies to all new ships, to existing ships not previously carrying such
equipment, and to ships having their equipment replaced. This means that all system
components covered by annex A1 must be type-approved accordingly and must carry the
Wheelmark, which is a symbol of conformity with the Marine Equipment Directive.

Navico has no responsibility for incorrect installation or use of the equipment. It is essential
for the person in charge of the installation to be familiar with the relevant requirements as
well as with the contents of the manuals, which covers correct installation and use.

Preface

 | R3016 12U/6X Installation manual

3

Summary of Contents for R3016 12U/6X









































Reviews: