manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

The Simrad GO XSE Series offers exceptional navigational capabilities and advanced features. Ensure seamless installation with the comprehensive "Installation Manual" available for "free download" at manualshive.com. This detailed "manual" provides step-by-step instructions for setting up your device, optimizing your experience on the water.

Share
Download
background image

Selecting the tuner region

Before using FM, AM or a VHF radio, you must select the appropriate
region for your location.

Radio channels

To tune in to an AM/FM radio channel:

•

press and hold the left or right audio control button

To save a channel as a favorite:

•

select the favorite menu option

To page through favorite channels:

•

select the up or down audio control button

List of favorite channels

The favorite list can be used for selecting a channel, and for deleting
the saved channels from the list.

Sirius radio

Ú

Note: 

Sirius radio is available in North America only.

If you have a compatible Sirius XM receiver connected to your
system, you can control the receiver from the Audio control bar.
Sirius service covers inland U.S. waters and coastal areas into the
Atlantic and Pacific oceans, Gulf of Mexico, and the Caribbean Sea.
The SiriusXM products received vary depending on your selected
subscription package. For more information, refer to
www.siriusXM.com and the server documentation.

Lists of Sirius channels

Several options are available for displaying the Sirius channels.

184

Audio

 | GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Panasonic WJHD309A - DIGITAL DISK RECORDER Network Operating Instructions preview
WJHD309A - DIGITAL DISK RECORDER
Brand: Panasonic Pages: 79
LAWO crystal User Manual preview
crystal
Brand: LAWO Pages: 459
earline 60700 User Information preview
60700
Brand: earline Pages: 13
Ocmis Irrigazione MR Instructions For Use Manual preview
MR
Brand: Ocmis Irrigazione Pages: 100
Garmin GMR 404 Release Note preview
GMR 404
Brand: Garmin Pages: 2
Hammer Strength MTSP Unpacking And Assembly Instructions preview
MTSP
Brand: Hammer Strength Pages: 18
Nautilus F3 0-90 Manual preview
F3 0-90
Brand: Nautilus Pages: 17
National Instruments PXIe-8240 Getting Started Manual preview
PXIe-8240
Brand: National Instruments Pages: 6
Qlight S80S Manual preview
S80S
Brand: Qlight Pages: 3
qtran Q-VAULT-5 Installation preview
Q-VAULT-5
Brand: qtran Pages: 2
Q-Optics Radiant Instructions & Care preview
Radiant
Brand: Q-Optics Pages: 2
Uniden HH940 Manual De Usuario preview
HH940
Brand: Uniden Pages: 23
YOKOGAWA AQ7280 OTDR Getting Started Manual preview
AQ7280 OTDR
Brand: YOKOGAWA Pages: 75
BARRON Exitronix LEMD Series Installation Instructions Manual preview
Exitronix LEMD Series
Brand: BARRON Pages: 6
Ocean Signal EPIRB2 User Manual preview
EPIRB2
Brand: Ocean Signal Pages: 2
PAC RadioPRO 4 RP4-MZ11 Quick Start Manual preview
RadioPRO 4 RP4-MZ11
Brand: PAC Pages: 5
AGCO Glencoe CM41 Operator'S Manual preview
Glencoe CM41
Brand: AGCO Pages: 44
Braun Aesculap S4 FW103R Instructions For Use/Technical Description preview
Aesculap S4 FW103R
Brand: Braun Pages: 39

Brands by name

Popular brands

Load more brands