manualshive.com logo in svg

Simrad GO XSE Series, Operator'S Manual

Share
Download
Simrad GO XSE Series Operator'S Manual Download Page 172

ForwardScan

About ForwardScan

ForwardScan sonar is a navigational aid that helps you monitor the
underwater environment in front of your vessel while carrying out
slow speed maneuvers.
To use the ForwardScan feature you must have a ForwardScan
transducer mounted on your vessel.
The ForwardScan transducer must be connected to a compatible
sonar module (or another unit which has built-in sonar shared over
the network).

 Warning: 

Do not rely on this equipment as your

principle source of navigation or hazard detection.

 Warning: 

Do not use this equipment to gauge depth

or other conditions for swimming or diving.

The ForwardScan image

A

Depth range scale and vessel position

B

Forward range scale

C

Point data

17 

172

ForwardScan

 | GO XSE/XSR Operator Manual

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands