Simrad GO XSE Series Operator'S Manual Download Page 134 | Manualshive

Page: 134 / 242

background image

•

Range markers

•

Compass

•

Heading line

•

Active route

Radar panel symbology can be collectively turned on/off from the
Symbology option in the More sub-menu if they are selected to
show in the radar settings dialog.

Bearings

Used for selecting whether the bearing should be measured in
relation to True/Magnetic North (°T/°M), or relative to own vessel
(°R).

Ú

Note:

True bearing can only be selected when a compass is

available.

Data bar

Turns on/off the radar data bar. Refer to the radar panel illustration.
By default, the data shows targets arranged with the most
dangerous targets on top. You can select to show radar targets on
top and before any AIS targets, even if the AIS targets are
considered more dangerous.

Vessels and tracked targets

This dialog contains settings for both AIS and radar targets. AIS
specific settings are only available if you have a capable AIS device
connected to your system.
Use this option to specify:

134

Radar

| GO XSE/XSR Operator Manual

«
...
132
133
134
135
136
...
»

Summary of Contents for GO XSE Series



















































































































































































































































Reviews:

No comments

Related manuals for GO XSE Series

Brand: Abicor Binzel Pages: 92

Brand: Nakayama Pages: 37

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Contrology Cadillac

Brand: Balanced Body Pages: 7

Brand: Fast Pages: 60

Brand: Ideal Heating Pages: 16

i-Digits Access

Brand: Össur Pages: 231

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brand: Gilson Pages: 8

Brand: Kattsafe Pages: 19

Brand: Numark Pages: 11

Brand: E-FLOR Pages: 124

Brand: Elenco Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands