background image

Page

26

9.3 

Failure Subsystem

Excessive intake/exhaust temperatures, any reduction in cooling air flow, or a Loss of 

Communication from either the hand-held controller or the controlling load bank is 

indicated by the illumination 

of the “Error” indicator on the

hand-held remote control. 

Any of the above conditions 

will result in the load bank 

entering a failure state. The 

“Failure” indicator on the 

hand-held controller will 

illuminate and the load de-

energizes. All load steps are 

locked out until the problem is 

corrected. Until the failure is 

investigated/corrected and the control system is reset the load cannot be reapplied.

Problem

Cause

Resolution

High Exhaust

The unit has 

overheated due to: 

1

The fan has 

stopped running.

The unit needs to be serviced. 

Please contact a technician for 

your problem.

2

The unit lacks 

sufficient exhaust 

space.

Move the unit to an area that 

allows for proper air circulation.

Metering Sys Fault

 Communications failure between PLC and 

meter.

Turn the unit off, disconnect all 

power cables, and wait a couple 

of seconds. Reapply power and 

turn the unit on. If the problem 

persists, contact a technician for 

your problem.

 Over KW/Under KW

Metered load does not match expected 

load.

The connection may be loose 

or the wire may have become 

disconnected. Please contact a 

technician for your problem.

Slave # Failure

When multiple units are chained together, the primary unit will display “Slave [Unit 

Number] Failure.” You must inspect that unit to resolve the failure.

Table 5 Trouble Shooting Table

WARNING

If a failure occurs during Load Bank opera

-

tion, the Load Bank will de-energize all load 

steps The operator must reset the Load 

Bank by turning it “Off” then “On.” The 

load failure must be investigated and cor

-

rected before load application can resume.

Summary of Contents for NORTHSTAR 125 KW




































Reviews: