Introduction
Congratulations on your purchase of the Sima SUP-60 Universal Power Adapter. It
can power digital cameras and other portable electronic devices requiring 3.3 / 4.2 / 5.0
/ 6.5 / 8.4 or 9.5V DC power. It is fully regulated using high efficiency switching technology
and features overload and short circuit protection. The SUP-60 comes with seven
connectors to fit different digital cameras and other electronic devices. Additional
connectors are available from Sima.
This package Includes:
1 AC adapter 7 Center pin positive connectors
1 SUP-60
Manual
Operation
1. Set the output voltage switch, as illustrated in Fig. 1, to the
desired output for your device. Choose from the following
settings: 3.3 / 4.2 / 5.0 / 6.5 / 8.4 or 9.5 V.
The SUP-60 comes with seven standard connectors. The
connectors allow you to match the size of your device’s DC
input jack. If your device requires other types of connectors,
visit Sima’s customer service at
www.simacorp.com.
The connectors supplied with the SUP-60 are all set in a
center pin positive alignment ( Fig. A)
If your device
requires a center pin negative power source (Fig. B) do
not use this adapter.
To determine the required current
and correct polarity for your device, refer to the
manufacturer’s instruction manual or specifications
2. Select the appropriate connector and attach it to the output socket at the end of the
output cord. To identify the correct connector for your device, see the list of digital
cameras on the reverse side of this sheet. If unsure, use the connector that fits the
power jack of your camera. The two-pin connectors can fit into the socket only one
way. Align the pins as shown at right in Fig. 2. One pin is larger
than the other. Do not force.
3. Insert the connector into the power jack on your portable device.
4. Plug the AC adapter into the SUP-60’s input power jack
located at the top of the unit.
Note: Do not plug the AC
adapter directly into anything except the SUP-60.
Next,
plug the AC adapter into a standard AC wall outlet. The red
power light on the SUP-60 should turn on. You can now
operate your device.
IMPORTANT:
Your portable device must be rated between 3 - 10V
DC and no more than 2100 mA of current to use the SUP-60. If
the exact voltage for your device is not listed below and is less than 10V, you can try
setting the voltage switch to the nearest voltage – use the lower setting first. If the
device does not operate, disconnect the connector from the device, reset the voltage
switch to the next higher setting and re-connect.
Do not continue trying higher
settings as they may result in damage to your device or the adapter.
The SUP-60’s current (mA) must be equal to or greater than the current your portable
device requires. Remember 1A = 1000mA, 0.5A = 500mA. Use the following chart
to determine the output current from the SUP-60:
Output Max.
Output Max.
Voltage Current
Voltage Current
3.3V = 2.1A
6.5V = 1.7A
4.2V = 2.0A
8.4V = 1.6A
5.0V = 1.9 A
9.5V = 1.5A
Resetting the Adapter
CAUTION
:
If the power light turns off, check the power source. If on, the output current
may be beyond the AC adapter’s specifications and overload protection has been activated.
To reset the adapter:
1. Remove the SUP-60 from the AC outlet and the device you are powering. Wait 10 sec.
2. Plug the SUP-60 into the AC outlet again. If the indicator remains off, there may be a
problem with the AC adapter. Contact Sima’s customer service for assistance.
Model SUP-60
For use with
digital cameras and camcorders.
Fig. 1
Output
Voltage
Switch
Power
light
120 VAC
Output
socket
Fig. 2
Connector
Output
socket
90-day Limited Warranty
Sima Products Corporation warrants this
product against defects in materials and
workmanship for a period of 90 days from the
date of purchase. During the warranty period,
the product will be repaired or replaced at
Sima’s option. Mail the enclosed product
registration card within ten days of the original
purchase.
Conditions:
Ship your unit, freight pre-paid,
including reasonable proof of date and place
of purchase and description of problem to:
Sima Products Corporation
Attn: Customer Service
140 Pennsylvania Ave.
Bldg. #5
Oakmont, PA 15139
This warranty is void if any defects are caused
by abuse, misuse, negligence or unauthorized
repairs.All liability for incidental or
consequential damages is specifically
excluded. Some states do not allow for the
exclusion or limitation of incidental or
consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights
and you may have other rights, which vary
from state to state.
Universal Power Adapter
Input
+
-
Fig. A
OK
-
+
Fig. B
No
Can’t find y
our plug?
Visit our websit
e
2
www.simacorp.com
