Silicon Laboratories EFR32xG14 Wireless Gecko, Reference Manual

Share

Page: 48 / 1140

Silicon Laboratories EFR32xG14 Wireless Gecko Reference Manual Download Page 48

Address Range

Module Name

0x400E2000 - 0x400E3000

LDMA

0x400E1000 - 0x400E1400

FPUEH

0x400E0000 - 0x400E0800

MSC

4.2.5 Bus Matrix

The Bus Matrix connects the memory segments to the bus masters as detailed in

4.1 Introduction

4.2.5.1 Arbitration

The Bus Matrix uses a round-robin arbitration algorithm which enables high throughput and low latency, while starvation of simultane-
ous accesses to the same bus slave are eliminated. Round-robin does not assign a fixed priority to each bus master. The arbiter does
not insert any bus wait-states during peak interaction. However, one wait state is inserted for master accesses occurring after a pro-
longed inactive time. This wait state allows for increased power efficiency during master idle time.

4.2.5.2 Peripheral Access Performance

The Bus Matrix is a multi-layer energy optimized AMBA AHB compliant bus with an internal bandwidth of 5x a single AHB interface.

The Cortex-M4, DMA Controller, and peripherals (not peripherals in the low frequency clock domain) run on clocks which can be pre-
scaled separately. Clocks and prescaling are described in more detail in

11. CMU - Clock Management Unit

. This section describes the

expected bus wait states for a peripheral based on its frequency relative to the HFCLK frequency. For this discussion, PERCLK refers
to a selected peripheral's clock frequency, which is some integer division of the HFCLK frequency.

Another factor that effects the cycle latency of peripheral accesses is the Peripheral Access Wait Mode (WAITMODE in MSC_CTRL)
configuration, which is present in some parts in the EFR32 series. For instance, when set to WS0, a higher throughput (in terms of
HFCLK cycles) is possible than with a higher wait state setting. However, this family of parts does not have configurable wait states.
Instead, refer to the access performance information for WS0 for this device family.

Reference Manual

Memory and Bus System

silabs.com

| Building a more connected world.

Rev. 1.1 | 48

«
...
46
47
48
49
50
...
»

Summary of Contents for EFR32xG14 Wireless Gecko





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands