manualshive.com logo in svg

Silicon Graphics ICE XA, Hardware User'S Manual, Page: 41 / 96

Share
Download
Silicon Graphics ICE XA Hardware User'S Manual Download Page 41

System Models

007-6399-002

 23

Figure 3-1

SGI ICE XA Series System E-Cell Assembly Example

The compute rack enclosures within the SGI ICE XA system are 10.5U 9-blade units. Each 
enclosure supports between two and nine compute blade assemblies, up to nine power supplies, 
one chassis management controller (CMC) and up to four InfiniBand based I/O fabric switch 
interface blades. Note that internal IB switch ASICs located in switch blades in the blade 
enclosure eliminate the requirement for external IB switches. The InfiniBand technology provides 
for fast communication between compute blades within the same chassis and also between 
compute blades in separate enclosures.

Optional water chilled D-rack cooling is available for support nodes and storage. Note that ICE 
XA blade enclosures require liquid-cooling and must reside in E-Cell racks and always require 
water cooling systems to operate. See the section Chapter 4, “Rack Information” for information 
on water-cooled ICE XA E-Cell systems.

Summary of Contents for ICE XA

































































































Reviews:

No comments