manualshive.com logo in svg

Siklu EtherHaul, Operation And Maintenance Manual

Share
Download
Siklu EtherHaul Operation And Maintenance Manual Download Page 149

EtherHaul Operation, Administration and Maintenance Manual 

Page 149 

16 

Statistics 

The EtherHaul uses advanced RF and Ethernet counters to provide real-time 
performance statistics for radio transmission activities, Ethernet ports, VLAN traffic and 
QoS queues. 

The following statistics enable quick analysis of system and component performance in 
support of troubleshooting and diagnostics. 

 

RF statistics – displays RF statistic counters to identify radio errors and check the 
radio status history. The RF statistics consist of real time statistic counters since 
the last time the counters were cleared 

 

VLAN statistics - displays statistic counters of each EtherHaul link component per 
VLAN 

 

Ethernet statistics - displays Ethernet statistics counters per Ethernet port 

 

Queues statistics – displays statistics per egress queue 

This chapter describes the system's statistics. 

The statistics are presented in the dedicated 

Statistics

 page. 

Statistics can be exported to Excel by clicking the 

Export to Excel

 button next to 

the relevant table. 

16.1 

Radio (RF) Statistics Monitoring 

16.1.1 

RF Statistics Summary 

Summary of radio statistics – 96 intervals of 15 minutes (last 24 hours), recording the 
minimum and maximum values per interval of RSSI, CINR and Modulation profile. 

 

Figure 16-1 Statistics Page: RF Statistics Summary 

Summary of Contents for EtherHaul





























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands