SIGMATEK PIM 041-W Operating Manual Download Page 6 | Manualshive

Page: 6 / 36

background image

PIM 041-W

PANEL INTERFACE MODULE

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

l

Project planners

l

Technicians

l

Commissioning engineers

l

Machine operators

l

Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found on
our website

www.sigmatek-automation.com

Our support team is happily available to answer your questions.
Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

l

TP XX61

This and additional documents can be downloaded from our website or obtained through
support.

1.3 Contents of Delivery

1x PIM 041-W

1x 4-pin Phoenix connector plug

4x M3 TX10 Torx screws

Page 4

14.04.2021

«
...
4
5
6
7
8
...
»

Summary of Contents for PIM 041-W





































Reviews:

No comments

Related manuals for PIM 041-W

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 26

Brand: NAiS Pages: 199

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 179

Brand: Panasonic Pages: 23

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 20

INDUSTRY PAN9028

Brand: Panasonic Pages: 34

Brand: Kasco Pages: 3

Brand: Kamstrup Pages: 36

Brand: JFA Electronicos Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands