SIGMATEK HZS 7321 Technical Manual Download Page 8

Page: 8 / 52

HZS 7321

TOUCH OPERATING PANEL

Page 6

04.09.2020

Basic Safety Guidelines

2.1

Symbols Used

The following symbols are used in the operator documentation for warning and danger mes-
sages, as well as informational notes:

DANGER

Danger

indicates that death or serious injury

will occur

, if the specified

measures are not taken.



To avoid death or serious injuries, observe the all guidelines.

Danger

indique une situation dangereuse qui, faute de prendre les

mesures adéquates,

entraînera

des blessures graves, voire mortelles.



Respectez toutes les consignes pour éviter des blessures graves,

voire mortelles.

WARNING

Warning

indicates that death or serious injury

can

occur, if the specified

measures are not taken.



To avoid death or serious injuries, observe the all guidelines.

Avertissement

d’une situation dangereuse qui, faute de prendre les

mesures adéquates,

entraînera

des blessures graves, voire mortelles.



Respectez toutes les consignes pour éviter des blessures graves,

voire mortelles.

CAUTION

Caution

indicates that moderate to slight injury

can

occur, if the specified

measures are not taken.



To avoid moderate to slight injuries, observe the all guidelines.

Attention

indique une situation dangereuse qui, faute de prendre les

mesures adéquates,

peut

entraîner des blessures assez graves ou lé-

gères.



Respectez toutes les consignes pour éviter des blessures graves,

voire mortelles.

INFORMATION

Provides important information on the product, handling or relevant sections
of the documentation, which require attention.

Summary of Contents for HZS 7321





















































Search results

Summary of Contents for HZS 7321

Reviews:

Related manuals for HZS 7321

Brands by name

Popular brands

SIGMATEK HZS 7321, Technical Manual

Search results

Summary of Contents for HZS 7321

Reviews:

Related manuals for HZS 7321

Brands by name

Popular brands