SIGMATEK HZS 7321 Technical Manual Download Page 12 | Manualshive

Page: 12 / 52

background image

HZS 7321

TOUCH OPERATING PANEL

Page 10

04.09.2020

CAUTION

Handle the device with care and do not drop or let fall.

Prevent foreign bodies and fluids from entering the device.

The device must not be opened, otherwise it could be damaged!

The module complies with EN 61131-2.

In combination with a machine, the machine builder must comply with EN
60204-1 standards.

For your own safety and that of others, compliance with the environmental
conditions is essential.

The control cabinet must be connected to ground correctly.

To perform maintenance or repairs, disconnect the system from the power
supply.

2.4

Software/Training

The application is created with the software LASAL CLASS 2 and LASAL SCREEN Editor.

Training for the LASAL development environment, with which the product can be configured,
is provided. Information on our training schedule can be found on our website.

«
...
10
11
12
13
14
...
»

Summary of Contents for HZS 7321





















































Reviews:

No comments

Related manuals for HZS 7321

Brand: ABB Pages: 138

Brand: ABB Pages: 116

Relion 615 series

Brand: ABB Pages: 136

Brand: Gardena Pages: 100

Brand: IBM Pages: 72

Brand: Gantner Pages: 56

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: CAME Pages: 32

Brand: Farfisa Pages: 20

Brand: Racal Instruments Pages: 64

Brand: National Instruments Pages: 2

Brand: York Pages: 24

Brand: C&C Pages: 17

Brand: Frico Pages: 12

Micro850 series

Brand: Allen-Bradley Pages: 24

653 - AE Series

Brand: VAT Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands