manualshive.com logo in svg

Sigma 1-6P, Operating Manual

Share
Download
Sigma 1-6P Operating Manual Download Page 5

 

Konformitätserklärung 

(2006/42/EG; 2006/95/EG; 2004/108/EG) 

Declaration of Conformity 

 (2006/42/EG; 2006/95/EG; 2004/108/EG) 

Déclaration de conformité 

(2006/42/EG; 2006/95/EG; 2004/108/EG) 

 
 
Die nachfolgend bezeichnete Maschine wurde in Übereinstimmung mit den Richtlinien 
2006/42/EG; 2006/95/EG und 2004/108/EG hergestellt und geprüft. 
The following machine is manufactured and tested in compliance with directives 2006/42/EG; 
2006/95/EG und 2004/108/EG. 
La machine désignée ci-dessous est produit et examiné conforme aux directives 2006/42/EG; 
2006/95/EG und 2004/108/EG 
 
 
Bezeichnung der Maschine:   

Laborzentrifuge 

Machine: 

   Laboratory 

Centrifuge 

Désignation de la machine:   

Centrifugeuse de laboratoire 

 
Maschinentyp : 

 

 

1 – 6 P 

Type: 

     

Type de la machine:   

 

 

 
Bestell  Nr. :   

 

 

10056, 10055 

Part 

No.: 

    

Réf. usine: 

 

 

 

 
Normen: 

   EN 

61010-2-020:2007 

Standards: 

 

 

 

EN 61000-3-2:2006; EN 61000-3-3:1995, A2:2005 

Normes 

: 

   EN 

61326-1:2006 

 
 

Sigma Laborzentrifugen 

An der Unteren Söse 50 
D-37520 Osterode 
 
 
23.11.2007       
 
   Geschäftsführer 
   Managing 

Director 

   Directeur 

Gérant 

 

 
        ........................................................................ 
 

 

 

 

 

 

 

 

Fabr. Nr.     Serial  No.     Numéro de série 

 

 

 

 

 

 

 

 

 

 

1-6P 20071123.DOC

 

 

Operating Manual SIGMA 1-6P 

 

 

page 5 of 67 

05/2007 

Summary of Contents for 1-6P




































































Reviews:

No comments

Brands by name

Popular brands

Load more brands