manualshive.com logo in svg

Sifos Technologies PhyView PVA-3000, Reference Manual

Share
Download
Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 75

PVA-3000 Reference Manual 

December 2, 2019

 

                                   

Sifos Technologies

  

Page 
75 

Command 

Command Parameters 

Query 

Returned 
Parameters 

qpsa_config

 

ipAddr#1

  

<

ipAddr#2 ipAddr#3… ipAddr#8 

>

 

 

 

 

 

Preconfigures up to 8 PSA / PSL / PVA chassis’ for rapid 
switching between chassis connections using 

qpsa

 

command.   Must be executed before 

qpsa

 

can be used. 

ipAddr#1

  

First of up to 8 PSA/PSL chassis addresses 

ipAddr#2

  Second of up to 8 PSA/PSL chassis addresses 

…..

 

ipAddr#N

  

Last of up to 8 PSA/PSL chassis addresses 

qpsa

 

ipAddr

 

 

 

Switches from current PSA  / PSL / PVA chassis to a 
different  PSA  / PSL / PVA chassis in a small fraction of a 
second.   Chassis address specified must have been 
included in a prior 

qpsa_config

 

command. 

ipAddr

  PSA / PSL / PVA address to switch to. 

4.3. 

Test Port Connection and Passive Impairment Configuration 

The following commands are directed to specific test ports and generally used for static configuration of test resources 
at that port.   Whenever the 

port

 

parameter is provided, the default slot-port for that and all subsequent commands will 

be set, as will the command prompt.  These commands accept the broadcast configuration where 

port

= 99,99.  See 

Sections 2.1 and 2.2.8 for further information on these test port resources. 
 

Command 

Port 

Command Parameters 

Query 

Returned 
Parameters 

pva_connect 

<

port

> 

phy

 | 

through

 

? 

PHY

 | THROUGH 

Configures switching to either terminate to Test PHY or 
route Test Port through to Auxiliary Port.  

phy

  Terminate the test port to the Test PHY (

wake-up 

default

) 

through

  Connect the Test Port via low loss coupler to 

the Auxiliary Port 

pva_line 

<

port

> 

impair

 | 

normal 

<

pair12

 | 

pair34

 | 

all

> 

? 

IMPAIRED | 

NORMAL

 

+ 

ALL 

| PAIR12 | 

PAIR34

 

Inserts or removes a worst case IEEE 802.3 insertion 
loss (100M Cat5e) passive line simulator from the Test 
Port on 2 or 4 pairs of the LAN connection. 

impair 

 Inserts the 100M Cat5e passive line emulator 

normal 

 Removes or bypasses 100M Cat5e passive 

line emulator  (

wake-up default

) 

all

 

 Perform the connect or bypass on all four LAN pairs 

(

default

) 

pair12

 

 Perform the connect or bypass on LAN Pairs 1 

and 2 (Blue and Orange TIA pairs) without altering 
Pairs 3 and 4. 

pair34

 

 Perform the connect or bypass on LAN Pair 3 

and 4 (Green and Brown TIA pairs) without altering 
Pairs 1 and 2. 

pva_mismatch 

<

port

>

 

impair | normal <pair12 | pair34 | all>

 

? 

IMPAIRED | 

NORMAL

 

+ 

ALL

 

| PAIR12 | 

PAIR34

 

 

 

Inserts or removes an 11.5 dB line mismatch on all pairs 
or specified pairs.  Amplitude Noise Impairments are 
only enabled when in the normal state. 

impair

 

 

Inserts 11.5 dB line mismatch 

normal

 

 Removes the 11.5 dB line mismatch  (

wake-up 

default

) 

all

 

 

Perform the connect or disconnect on all four LAN 

pairs (

default)

 

pair12

 

 

Perform the line mismatch connect or 

disconnect on just LAN Pair 1 and 2 (Blue and Orange 
TIA pairs).   

pair34

 

 

Perform the line mismatch connect or 

disconnect on just LAN Pair 3 and 4 (Green and 
Brown TIA pairs).   

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands