manualshive.com logo in svg

Sifos Technologies PhyView PVA-3000, Reference Manual

Share
Download
Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 74

PVA-3000 Reference Manual 

December 2, 2019

 

                                   

Sifos Technologies

  

Page 
74 

PowerShell PSA commands, global variables, and other common syntactical constructs such as braces and brackets, 
math operators, etc.  It provides many powerful capabilities that support authoring and troubleshooting bug-free scripts. 

 

To configure + for PowerShell PSA, first install +, then use the 

Language

 drop-down menu to 

Define Your Language

…, then select the 

Import

 control and import the file 

PowerShell_PSA.xml

 from the installed 

directory for PSA software.   This will typically be 

c:\Program Files (x86)\Sifos\PSA1200\

 on a Windows computer. 

 

4.2. 

PowerShell Connection and Configuration Commands 

PowerShell configuration commands are specific to a PowerShell (console) window.   The commands only affect that 
window and will have no immediate impact to any other PowerShell windows.  Settings for 

pva

 (IP Address) and the 

DUT Local Configuration File will be remembered from the most recent session of PowerShell PSA or PVA 
Interactive. 

 

Command 

Command Parameters 

Query 

Returned 
Parameters 

pva 

 

(alias to 

psa

) 

ipAddress

 

?

 

Current Chassis 
IP Address 

Selects the chassis to which subsequent commands and 
queries will be directed

. 

ipAddress

 

 

An n.n.n.n format IP address.  This address will 

apply until re-established by the 

pva

 command and is 

persistent if the shell is closed or computer is re-booted.

 

pva_demo

 

<

ON

 |

OFF

> 

slots

 

num_blades

 

 

 

This command enables or disables the Demo Mode for the 
PVA-3000.

 

ON:

  

Enable Demo (Emulation) Mode 

OFF:

  

Disable Demo (Emulation) Mode 

– must be connected 

to an instrument. 

numblades

:  The number of populated test slots (1-12) 

pva_version

 

Outputs current version of PowerShell PVA software. 

 

Module Versions 

pva_exists 

 

(alias to 

psa_exists

) 

ipaddress

 

 

1 =PSA found 

0 =No PSA found 

Returns “1” if PSA is found on network and “0” if PSA is not 
found on the network. 

 

ipaddress

:  The IP address of a PSA chassis.

 

pva_dut

 

dut_name

 

 

 

Loads the DUT-specific configuration file for a specific DUT 
type.  The DUT-specific configuration file specifies the 
following attributes to PowerShell: 

 

MAX_RATE:

 Maximum DUT link rate (10 | 100 | 1000) 

POLARITY:

 MDI_Only | MDI-X _Only | Both 

DUT_CLASS:

 SWITCH | OTHER 

PVA_TEST_RESULTS_PATH:

 Reporting subdirectory  

calport

 

<

port

> 

 

slot

,

port

 

 

Returns the designated calibration port given a Test Port.  If 
Test Port is x,1, Calibration Port is x,2 and if Test Port is x,2, 
Calibration Port is x,1. 

psa_latency_test

 

<

ipAddr

> 

 <

ioCount

>  <

-v

> 

PSA Address, 

Measurement Count, 

Minimum Latency (msec),  

Maximum Latency (msec),  

95th Percentile Latency 
(msec),  

I-O Status: 

OK

 | 

WARNING

 

| 

PROBLEM!

 

PROCESS_STATUS: 

OK

 | 

WARNING 

| 

PROBLEM!

 

Utility to statistically analyze network connection latency 
between host computer and PSA instrument and process 
preemption delays within the host computer.   The command 
will report Minimum, Maximum, and 95th Percentile values 
for I-O response time for specified interactions with a 
specified PSA address.  It will also categorize I-O response 
time and internal process execution integrity.  See Section 
2.5 for information about Network Connection Latency. 

ipAddr

:  IP address of PSA Instrument to which connection 

latency is being studied.   Default address is currently 
connected PSA instrument. 

ioCount

:  Count of latency measurements to be performed.  

Range is 100 to 2000 measurements.  .  Default value is 
100 measurements.   Higher counts will catch more 
intermittent problems. 

-v

:  Produce diagnostic details from the psa_latency_test 

utility.  Default is no diagnostic details. 

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands