Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 49 | Manualshive

Page: 49 / 134

background image

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
49

The remaining two options can be selected for any Link Speed but will only be in effect if the Link Speed is
100BaseTx or 1000BaseT.

Maximum Fixed

sensitivity sets a fixed gain of “8 out of 10” and would be appropriate

when attempting to link to very weak, low amplitude signals at 100/1000BaseT.

Minimum Fixed

sensitivity sets a

fixed gain of “2 out of 10” and would be useful given very short links to a high amplitude signal.

When any Receiver Sensitively setting is selected, the

Apply Rx Level

button will annunciate red and the new level

will be applied, following by an automatic re-link when

Apply Rx Level

is pressed.

3.8.5.

Link Config Actions Sub-Menu

The

Actions

sub-menu allows link configuration settings to be replicated on one or more

other test ports in the currently connected PVA instrument. This menu (

see Figure 3.17

)

provides check boxes for each link configuration sub-menu specifying whether those
settings should be copied (or replicated) to other test ports. For example, if

Link Config

and

Gigabit Config

are checked while the others are not, then only the Link Config (e.g.

Link Speed

,

Link Duplex

,

Link Polarity

) and the

Gigabit Config

settings will be

duplicated on other test ports.

Pressing the

Copy Settings

button opens the port replication dialog explained earlier in

Section 3.7.

3.9.

Link Monitor Menu

The

Link Monitor

tab menu (

see Figure 3.18

) serves three purposes:

1.

Configure Link Monitor

5.

Perform Link Monitor Measurements

6.

Perform Link Partner Assessments

The configurations performed in the Link
Monitor menu only apply to the Link
Monitor metering. As with previously
described menus, there is a

Read Settings

and a

Copy Settings

button.

Read

Settings

will update the displayed

configuration of the Link Monitor to match
the actual configuration. As noted before,
this is not routinely necessary since
changing test ports and tab menus will
automatically upload the most current
configuration settings from the test port.

Copy Settings

will open the port

replication dialog explained earlier in
Section 3.7. This enables replicating Link
Monitor configurations from the current
port to other available PhyView Analyzer
test ports. Copy Settings will also cause
any pending configuration setting changes
to be applied.

3.9.1.

Link Monitor Measurements

The

Link Monitor

was introduced earlier in Sections 1.3.12 and 2.2.2. This resource is used for assessing

Link Status

and

Link Stability

. Link Status refers to a collection of parameters that include:



Link State

(LINKED or UNLINKED)



Link Speed

(10, 100, or 1000)



Link Polarity

(MDI or MDI-X)



Duplex Mode

(FULL or HALF)



Gigabit Mode

(MASTER or SLAVE)



Pair 1&4 Polarity

(SWAPPED or NOT_SWAPPED)

Figure 3.17

Link Config

Copy Settings

Figure 3.18

Link Monitor Tab Menu

«
...
47
48
49
50
51
...
»

Summary of Contents for PhyView PVA-3000







































































































































Reviews:

No comments

Related manuals for PhyView PVA-3000

Brand: JAMAR Technologies Pages: 4

Brand: Jamar Pages: 60

Brand: M-system Pages: 13

NANOCOLOR Advance

Brand: Macherey-Nagel Pages: 45

Brand: NARDA Pages: 64

Brand: Lasertec Pages: 21

Brand: LOVATO ELECTRIC Pages: 10

Brand: e-sylife Pages: 2

LaserDIMENSIONMASTER 3336

Brand: Calculated Industries Pages: 2

BIP LD2-T017-01-EP-S4 Series

Brand: Balluff Pages: 16

Brand: janitza Pages: 96

Brand: Groz Pages: 12

Brand: Cal Test Electronics Pages: 20

Brand: Lisle Pages: 8

STARGAS 898 LIGHT

Brand: tecnotest Pages: 146

FST-2000 TestPad

Brand: Acterna Pages: 6

Brand: Sonel Pages: 88

Brand: Lufkin Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands