Sifos Technologies PhyView PVA-3000 Reference Manual Download Page 38

Page: 38 / 134

PVA-3000 Reference Manual

December 2, 2019

Sifos Technologies

Page
38

Port

Connection Mode

Parameter

Specification

THRU Port
for Packet
Analyzers

Bypass Mode THRU Port to TEST
Port

(

terminated 100



/ pair

)

Connection

RJ45

Data Rate and Signaling

10/100/1000BaseT

Impedance

100Ω, Balanced

Insertion Loss (1

–100 MHz)

2.7 +0.3, -0.2 dB (All Pairs)

Return Loss (All Pairs)

≤ -15 dB, 1MHz to 100MHz

Pair-Pair Isolation (All Pair
Combinations)

≤ -33 dB, 1 MHz to 100MHz

2.7.3.

Link Partner Transmitter / Incoming Link Integrity Measurements

Measurement

Link Types & Pairs

Parameter

Value

Power Spectral
Distortion

100Base-Tx: Pair 2 or 3

1000Base-Tx: Pairs 1 to 4

Minimum Frequency

20 KHz

Maximum Frequency

100 MHz

Selectable Range

0.18 MHz

– 99.98 MHz

Frequency Resolution

Selected Range / 33 Points

Amplitude Range

≤ -30 dB to ≥ +3 dB

Amplitude Accuracy

normalized to calibration

± 0.5 dB (.02

– 75 MHz)

± 1.5 dB (75

– 100 MHz)

Ideal Gigabit Config. @ DUT

MDI, MASTER

Signal-To-Noise

100Base-Tx: Pair 2 or 3

1000Base-Tx: Pairs 1 to 4

Measurement Range

18.5 dB

– 36 dB

Measurement Accuracy

± 1.5 dB (SNR > 30 dB)

± 0.75 dB (SNR

≤ 30 dB)

Ideal Gigabit Config. @ DUT

NONE

Power Level

100Base-Tx: Pair 2 or 3

1000Base-Tx: Pairs 1

– 4

Measurement Range

≤ -15 dB to ≥ +3 dB

Accuracy / Repeatability

± 0.25 dB

Ideal Gigabit Config. @ DUT

NONE

Bulk Echo
Response

(~ 4

– 75 MHz)

1000Base-T: Pairs 1 to 4

Measurement Floor

-26 dB

Accuracy / Repeatability

normalized to calibration

± 1.0 dB @ > -20 dB

± 1.5 dB @

≤ -20 dB

Ideal Gigabit Config. @ DUT

MDI, MASTER

Bulk Crosstalk
Response

(~ 4

– 75 MHz)

1000Base-

T: Pair Combo’s

1-2, 1-3, 1-4, 2-3, 2-4, 3-4

Measurement Floor

-39 dB

Accuracy / Repeatability

normalized to calibration

± 1.0 dB @ < 32 dB

± 1.5 dB @

≥ 32 dB

Ideal Gigabit Config. @ DUT

MDI, MASTER

Pair Timing Skew

1000Base-T: Pairs 1 to 4

Range & Resolution

– 80 nsec, 8 nsec

Ideal Gigabit Config. @ DUT

NONE

100BaseT and 1000BaseT SNR measurements are not referenced to any metric standards for SNR. SNR is a bulk

measure of signal deviation from “ideal” given compensation for linear distortion and other correctable impairments.

2.7.4.

Link Partner Receiver / Link Integrity Measurements

Measurement

Link Types &
Pairs

Parameter

Value

Link State and

Link Integrity

10/100/1000BaseT

Link Status

LINKED | DOWN

1000BaseT

Remote Rx Status | Local Rx Status

Rx_ OK | Rx_Error

10/100/1000BaseT

Status Samples

1 to 100

Status State Sampling Periodicity

20, 50, or 100 msec

Internal Test Port Packet
Counting

10/100/1000BaseT

Packet Frame

Ethernet MAC

Packet Size & Resolution
(

excluding 4 FCS Bytes

)

60 to 1512 Bytes, 4 Bytes

Packet Payload

Repeating 4-Byte Patterns

Packet Address

6-Byte Arbitrary Address

Transmitted Inter-Packet Gap Time

96, 576, or 11006

payload bit periods

Transmitted Packet Count

0 = Continuous

32K, 128K, 5120K, or
1024K

Received Packet Count

0 to > 1e9

Receive Packet Filtering

NONE

Summary of Contents for PhyView PVA-3000







































































































































Search results

Summary of Contents for PhyView PVA-3000

Reviews:

Brands by name

Popular brands

Sifos Technologies PhyView PVA-3000, Reference Manual

Search results

Summary of Contents for PhyView PVA-3000

Reviews:

Brands by name

Popular brands