Sifam Tinsley N20ZPLUS User Manual Download Page 7

N20Z

PLUS

User’s Manual 

 6

 

5.4. 

Parameter description 

5.4.1.  Display 

The  display  can  be  configured  by  changing  the  settings  of  the  following 

parameters: 
a)

display  colors  of  the measured  value.  The display  range  is  divided  into  three

areas separated by threshold values KpL and KpH (respectively lower threshold KpL
and  upper  threshold  KpH  of  the  change  of  the  display  color  -  Fig.  7).  The  color  of
displayed  numbers  for  each  area  is  selected  from  three  available  colors:  green,
orange  and  red.  The  KpL  and  KpH  values  are  set  by  the  user  and  refer  to  the
displayed value (i.e. also include individual characteristics). By default, the KpL value
is  equal  to  100%  of  the  nominal  value,  while  KpH  is  equal  to  110%  of  the  nominal
value, e.g.: for the 400 V meter: for KpL - 400 V and for KpH - 440 V  respectively.

Caution!  After  setting  the  individual  characteristic,  KpL  and  KpH  are  not 

automatically updated.

 

Fig. 7. display color configuration 

b)

decimal  point  -  measurement  precision.  There  are  5  possible  display

configurations to choose from, but you should take the accuracy of the measurement
into  account,  for  example:  for  the  400  V  range  -  the  measurement  error  is  2  V,  so
choosing  a  precision  with  two  decimal  places  does  not  give  you  more  accurate
measurements. For version with voltage measurement the factory setting of precision
is 0000.0; for version with current measurement - 00,000.
c)

unit backlight. Unit backlight can be turned on or off. It is on by default.

5.4.2.  Measurement parameters 

We can configure the measurement by changing the following: 

a)

input type: AC measurement, AC+DC measurement (True RMS), AC

measurement is factory default,
b)

averaging time: until the required number of correct measurements is obtained

(according  to  table  1),  the  instantaneous  value  from  1  measurement  is  displayed.
After  measuring  a  certain  number  of  measurements,  the  arithmetic  mean  of  the
measured measurements is displayed. Subsequent measurements are added on the

di

s

pl

ay

ed

 v

a

lu

e

 

KpH 

KpL 

Summary of Contents for N20ZPLUS




















Reviews: