Sierra Wireless Airlink Raven XE H2225E Manual Download Page 1

 

Page 

1

 of 

9

 

 

Sierra Wireless Airlink Raven XE H2225E Router 

 

Description 

The target of the Airlink Raven XE is the Alarming Module.  Its purpose is to Send and Receive SMS 
messages.  Essentially, it is going to be utilized as an SMS gateway.  As an example, Ignition picks up 
information from a PLC that the water temperature is too hot.  Ignition send an SMS message via the 
Raven XE to contacts assigned to that alarm.  It is received by a contact, which is then acknowledged via 
SMS by the contact.  This SMS message is sent back and received by Ignition via the Raven XE. 
 

Raven XE and Network Security 

The security settings covered here are basic steps to secure the Raven XE.  Inductive Automation is not 
responsible for the security of your Raven XE.  You should take the time to configure and test the 
current and other security measures as appropriate to your network. 
 
Inductive Automation tested this router as a device that sits inside a network.  Therefore, it needs to be 
configured to act simply as another device on the network, not as a router or DHCP Server etc.  Its sole 
purpose is to handle SMS traffic.  The setup steps below cover these.  If you wish to utilize its other 
features, bear in mind that you will need to ensure it works properly on your network and is secure. 
  

Configuration and ACEManager 

To access and change the modem’s configuration information, you will be accessing what is called the 
ACEManager.  This can be accessed via Ethernet, USB or Serial.  This document will only cover Ethernet 
access.  The recommended browser to use is IE or Firefox.  ACEManager run poorly under Safari and 
Chrome. 
 

Setup Steps 

 
The sections below should be followed in the order given to setup the Raven XE H2225E.  Note that any 
change that is made usually requires a reboot of the modem, which can be done through the 
ACEManager.  Follow these instructions and reboot at the end.  
 

Default Ethernet Connection 

First connect the Raven XE directly to your computer and follow the manual’s instructions to 
connect to it. 
 

Default Ethernet settings for access is: 

Device IP Address: 192.168.13.31 
Port: 9191 
Username: user 
Password: 12345 

 

Summary of Contents for Airlink Raven XE H2225E










Reviews: