background image

en

    Additional programme settings/options

40

Less Ironing  *

(

æ

)

Settings that can be selected: 

on

 – 

off

Reduces creasing thanks to a special 

spin sequence followed by fluffing and 

reduced spin speed.

Note:  

The washing's residual moisture 

is increased.

Soak  *

(

õ

)

Settings that can be selected: 

on

 – 

off

Before the main wash cycle starts, the 

washing remains for longer in the water 

to partially dissolve intensive soiling.
To be used for particularly stubborn 

soiling.
Dose the detergent using i-Dos or add it 

into the 

À

 

Á

 compartment in 

accordance with the manufacturer's 

instructions.

Notes

Load laundry of the same colour.

If your machine does not have this 

option, you can soak as follows:

1.

Select i-Dos or dose detergent in the 

À

 

Á

 manual compartment in 

accordance with the manufacturer's 

instructions.

2.

Select the 

Cotton 30 °C

 programme 

and the 

Ü

 button.

3.

Press the 

Ü

 button after approx. 10 

minutes. The laundry remains in the 

soaking solution.

4.

Leave the laundry to soak for as long 

as required, then either press the 

Ü

 

button again to continue the 

programme or change the 

programme.

Note:  

No additional detergent is 

required; the soaking solution is 

used for washing.

Rinse Hold  *

(

$

)

Settings that can be selected: 

on

 – 

off

The washing remains in the water after 

the last rinse cycle. End the programme 

~

 Page 45

Silent Wash *

(

ç

)

Settings that can be selected: 

on

 – 

off

Reduced noise values thanks to special 

wash and spin cycle and deactivated 

end signal. Especially suitable for 

washing at night.

Note:  

Residual moisture of the washing 

is slightly increased.

www.devicemanuals.eu/

Summary of Contents for WM14YH89GB









































































Reviews: