Siemens WM14W790AU Instruction Manual And Installation Instructions Download Page 40

Page: 40 / 56

Operating the appliance

Adding laundry

After starting the programme, you can

add or remove laundry if necessary.
Press the

button to do this.

The

button indicator lamp flashes

and the machine checks whether it is

possible to add laundry.

If the following appears in the display

panel:

■

Both

the - P - and

symbols light

up, it is possible to add laundry.

■

- P - lights up, it is not possible to

add laundry.

To continue the programme, press the

button. The programme continues

automatically.

Notes

■

Do not leave the door open for too

long when adding laundry as water

from the laundry may leak out.

■

For safety reasons, the door remains

locked when the water level or

temperature is high, while the drum

is turning or during the active oxygen

phase, and it is not possible to add

laundry during this time.

■

It is possible to add laundry during

the sensoFresh

programme.

■

The load display is not active during

reloading.

Changing the programme

If you have started the wrong

programme by mistake, you can

change the programme as follows:

Press the

button.

Select another programme.

Press the

button. The new

programme starts from the

beginning.

Note:

When switching from

programmes that use active oxygen to

those that do not, the door will remain

locked for up to 25 minutes until there

is no longer any active oxygen in the

drum.

The

and

symbols will flash. If the

symbols are off, the door can be

opened.

Cancel the programme

For programmes at high temperatures:

Press the

button.

To cool down laundry: Select

Rinse

Press the

button.

For programmes at low temperatures:

Press the

button.

Select

Spin

Drain

Press the

button.

Note:

When cancelling programmes

that use active oxygen, the door will

remain locked for up to 25 minutes until

there is no longer any active oxygen in

the drum.

Switch the appliance on again if

necessary. The

and

symbols will

flash. If the symbols are off, the door

can be opened.

Programme end during rinse

hold

In the display panel,

flashes, and the

preset spin speed and remaining

programme length are displayed for the

selected programme.

Continue the programme by:

■

Pressing the

button or

■

Changing the spin speed, or setting

the programme selector to

Drain

and then pressing the

button.

Summary of Contents for WM14W790AU

























































Search results

Summary of Contents for WM14W790AU

Reviews:

Related manuals for WM14W790AU

Brands by name

Popular brands

Siemens WM14W790AU, Instruction Manual And Installation Instructions

Search results

Summary of Contents for WM14W790AU

Reviews:

Related manuals for WM14W790AU

Brands by name

Popular brands